Panasonic TH-50PWD6 PC Input Terminals connection, Signal Names for D-sub 15P Connector

Page 8

Connections

PC Input Terminals connection

COMPUTER

AUDIO

PC IN

Conversion adapter

Less than

Ferrite core (large size)

3" 15/16

(if necessary)

 

(supplied)

 

 

(10 cm)

D-sub 15p

 

 

 

RGB

 

 

 

PC cable

 

Ferrite core (small size)

Less than

 

3" 15/16

 

 

(supplied)

(10 cm)

Audio

Stereo plug

Connect a cable which matches

the audio output terminal on the computer.

Installing the ferrite core (Small size)

1

2

Pull back the tabs (in two places)

Installing the ferrite core (Large size)

1

2

Pull back the tabs (in two places)

3

Open

Press the cable through and close

3

Open

Press the cable through and close

Notes:

(1)Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

(2)The display resolution is a maximum of 640 480 dots (TH-42PWD6), 768 768 dots (TH-42PHD6), 1,024 768 dots (TH-50PHD6) when the aspect mode is set to “4:3”, and 852 480 dots (TH-42PWD6), 1,024 768 dots (TH- 42PHD6), 1,366 768 dots (TH-50PHD6) when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

(3)The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection.

(4)Some PC models cannot be connected to the set.

(5)There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal.

(6)The computer shown in the illustration is for example purposes only.

(7)Additional equipment and cables shown are not supplied with this set.

(8)Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range.

(9)Component Input is possible with the pin 1, 2, 3 of the D-sub 15P Connector.

Signal Names for D-sub 15P Connector

11 12 13 14 15

6 7 8 9 10

1 2 3 4 5

Pin Layout for PC Input Terminal

Pin No. Signal Name

1R (PR/CR)

2G (Y)

3B (PB/CB)

4GND (Ground)

5GND (Ground)

Pin No.

Signal Name

Pin No.

6

GND (Ground)

11

7

GND (Ground)

12

8

GND (Ground)

13

9

NC (not connected)

14

10

GND (Ground)

15

Signal Name

GND (Ground)

SDA

HD/SYNC

VD

SCL

8

Image 8
Contents Operating Instructions High Definition Plasma DisplayEnglish Model No. TH-42PWD6Table of Contents Important Safety Notice Trademark CreditsWhen using the Plasma Display Safety PrecautionsSetup Electric shocks can result if this is not done Cleaning and maintenanceIf problems occur during use Remote Control Batteries AccessoriesAccessories Supply Connections SpeakersTerminals L Speakers Terminals R AC cord connection see AC cord fixingSignal Names for D-sub 15P Connector GND Ground Signal NamePC Input Terminals connection SDA HD/SYNC SCLInstalling the ferrite core Large size CommandSerial Terminals connection Communication parametersBasic Controls Off Power On/Off and input signal selection Power On/OffConnecting the plug to the Wall Outlet AC cord connectionSelect the input signal Selecting the On-Screen Menu LanguageINPUT1 INPUT2 INPUT3 EnglishusOn-Screen Menu Displays Press to access each adjust screen From the unit Press to SetupTo setup Multidisplay screen Press to Set upAspect Controls Helpful Hint N / Normalise Normalisation Adjusting Picture Pos./SizeAdjusting screen Picture Adjustments NormalDynamic CinemaAdvanced settings AGCSound Adjustment MuteDigital Zoom Display the Operation GuideSelect the area of the image to be enlarged Select the magnification required for the enlarged displayPresent Time Setup / Set up Timer Present Time SetupPress to exit from Present Time Setup Present TimeSet up Timer Display the Set up Timer screen Press to selectMode selection Start settingScreensaver For preventing after-images Reversal / Scroll selectionPress to select Screensaver Setup of Screensaver TimeReduces screen after-image Side Panel Adjustment This function may be applicable to the non-picture areaINPUT3/VIDEO3/COMPONENT3/RGB3/PC3/DVD3/CATV3/VCR3/STB3 Reduces power consumptionCustomizing the Input labels Setup for Multi Display How to Setup Multi DisplayPress to select 2 ⋅ 2, 3 ⋅ Setup for Input Signals Component/RGB-in Select3D Y/C Filter For Ntsc AV images RGBColour system / Panasonic Auto Cinema realityIf the picture image becomes unstable PAL Secam NtscSetting RGB sync signal SyncFreq. kHz/V-Freq. Hz Displays the H Horizontal/V Vertical frequenciesTroubleshooting Plasma Display panel Symptoms CheckInput signal can be displayed MarkSpecifications TH-42PWD6 TH-42PHD6 TH-50PHD6Customer’s Record