Panasonic TH-5065PF10UK manual Safety Precautions / Maintenance, Setup, AC Power Supply Cord

Page 7

Safety Precautions / Maintenance

WARNING

Setup

Do not place the Plasma Display on sloped or unstable surfaces.

• The Plasma Display may fall off or tip over.

Do not place any objects on top of the Plasma Display.

•If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center.

Do not cover the ventilation holes.

•Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.

Transport only in upright position!

•Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry.

If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, 2 3/8” (6 cm) or more at the bottom, and 2 3/4” (7 cm) or more at the rear. If using some other setting-up method, leave a space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 2 3/4” (7 cm) or more at the rear.

AC Power Supply Cord

The Plasma Display is designed to operate on 120 V AC, 50/60 Hz.

Do not use any power supply cord other than that provided with this unit.

• Doing so may cause fire or electric shocks.

Securely insert the power cord plug as far as it will go.

•If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used.

Do not handle the power cord plug with wet hands.

• Doing so may cause electric shocks.

Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable.

•Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center.

If the Plasma Display will not be used for a long period of time, unplug the power cord from the wall outlet.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately.

•Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature.

If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.

•A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made.

Maintenance

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

•If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry.

•Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

•If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

•Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result.

•Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Please keep this manual for future reference Operating Instructions Manual de instruccionesEnglish Model No. Número de modeloRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits When using the Plasma Display Safety PrecautionsAC Power Supply Cord MaintenanceSafety Precautions / Maintenance SetupAccessories Supplied AccessoriesRemote Control Batteries See ConnectionsAC cord fixing Monitor terminalCovered HDMITerminal Board BNC Component Video ConnectionsOptional Terminal Board Insert Slot Equivalent of DualPC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorBasic format for control data CommandSerial Terminals connection Communication parametersDVD Hdmi connectionComponent / RGB connection RCA-BNCConnecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet Power on / OFF Menu Screen on / OFF Remote control sensor Volume AdjustmentMain Power On / Off Switch Power Indicator Basic ControlsBasic Controls Menu button on the unit can also be To Picture adjust menu Pressed Press to select SeeTo Sound adjust menu On-Screen Menu DisplaysOn-Screen Menu Displays Power on Time Power OFF TimeComponent INPUT1 INPUT2A INPUT2B INPUT3 PC Selecting the input signalInitial selections Selecting the On-Screen Menu LanguageNormal Full During Multi PIP OperationsDuring COMPONENT, RGB and PC input signal Adjusting POS. /SIZESize / DOT Clock / Clock Phase / 11 Pixel Mode Press to adjust POS. /SIZEAdjusting POS. /SIZE Multi PIP Press to confirm Off Sets normal two screen display modeOn Sets Advanced PIP mode Advanced PIPCinema Picture AdjustmentsStandard DynamicPicture Adjustments Advanced SettingsTreble Sound AdjustmentBass MIDMute Sound AdjustmentSDI Sound Output SurroundDigital Zoom Press to set up DAY or Present Time of DAY Present Time SetupButton Forward Display the SET UP Timer Screen Press to select SET UP TimerPower on Time / Power OFF Time Negative / Scroll selection Mode selectionStart setting Screensaver For preventing image retentionReduces screen image retention Setup of Screensaver TimeScreensaver For preventing image retention OFF Dark MID Bright Side BAR AdjustPress to exit from Screensaver Customizing the Input labels Reduces power consumptionAddition sign Selected Input Portrait Setup will be unavailable SET UP for Multi DisplayHow to setup Multi Display If you set Multi Display Setup to onPress to select Seam Hides Video Press to select OFF, on SET UP for Multi DisplayDisplay Number locations for each arrangement Examples Press to select OFF , on ID Remote Control FunctionID remote control button operation ID CancellationHow to setup Portrait SET UP for PortraitPress to select Seam Hides Video Viewing Area Location Location setting When Portrait Setup onDisplay the image of the selected Location Viewing Area and LocationComponent RGB SET UP for Input SignalsComponent / RGB in Select 3D Y/C Filter For Ntsc AV imagesRefresh Rate SET UP for Input SignalsPress Action button Press to exit from adjust mode Video NR / Block NR / Mosquito NRPulldown Color System / Panasonic AutoColor System Displays the H Horizontal / V Vertical frequencies Setting RGB sync signalSync FREQ. kHz / V-FREQ. HzOptions1/3 Options AdjustmentsOff Initial VOL Sets normal volume Level Options AdjustmentsWhen Disable is set, the Off-timer is cancelled Normalization Weekly Command Timer Press to set each item Press to select a command numberPress to select Time / Command Time Set the time to execute a command programShipping condition Plasma Display panel TroubleshootingCOMPONENT/RGB/PC/VIDEO input signals VGA60 COMPONENT/RGB/PC/VIDEO input signalsVideo input Hdmi MHz Active pixels Pixels Active lines LinesCommand list of Weekly Command Timer TH-50PF10UK TH-65PF10UK SpecificationsLimits and Exclusions Limited Warranty Statement Panasonic Canada Inc Customer’s RecordPanasonic Professional Display Company Executive Office
Top Page Image Contents