Panasonic TX-47P950A General Operation, Power Stand-by see, Multi Screen see

Page 11

General Operation

Power (Stand-by) (see page 6)

The TV set must first be plugged into the wall out- let and turned on at the power switch.

Press this button to turn the TV set On from Standby mode, press it again to turn the TV set OFF to Standby mode.

Note:

•It is also possible to turn the TV set on from STANDBY mode by pressing the “Direct Programme Number Se- lection” Buttons (0-9) and the “Programme Number Up or Down” Button, either on the set or on the Remote Con- trol.

Off timer (see page 23)

Multi Screen (see page 29)

Aspect (see page 28)

Surround (see page 26, 27)

Normalization (see page 25, 27)

Programme Number Selection Press to select the next higher or lower Programme number.

Press to store settings in Tuning menu.

TEXT hold (see page 32) /Still (see page 29)

TEXT Index (see page 33) /Channel Search (see page 30)

5

REC	VCR DVD

VCR/DVD CONTROL (see page 34)

TV/AV Mode Selection

Press to select TV, AV1, AV2, AV3 and AV4 input signal modes sequentially.

Remote control :	TV/AV

AV1 AV2 AV3 AV4

Press to display AV1 - AV4 at the bot- tom of the screen. Each coloured but- ton corresponds to each input signals. For example, pressing the Red button selects AV1.

Direct programme Number

•Direct Programme Number Selection You can select the number directly by pressing the corresponding programme number buttons.

Programme Number 8	8
Programme Number 36....	3	6
Programme Number 124...	1	2	4

Note:

•When the Skip setting for Programme Number 100 through 125 is on, the channel selection time will be short- ened, and thus you can not input three digits at a time.

TV

11

Image 11

Contents Wide Projection Television Operating InstructionsTable of contents Do not place in humid or Following on the unit FlowerFixing to a wall Safety Precaution Securing the castersBefore Operating This Set Headphones plug Connecting HeadphonesConnect headphones as follows Pull and hold the hook, then open the battery cover How to Turn the Power OnBattery Installation Battery cautionsRefer to Location of ControlsControls and Terminals on the TV Connections How to connect the AV1, 2, 3 or 4 Input TerminalsVHS VCR Connections How to connect the DVD Input TerminalsSTR General OperationMulti Screen see Power Stand-by seeVCR/DVD Control see TV/AV Mode Selection General OperationOn Screen Help ‘Instructions’ box On Screen menu Display from Remote ControlSee Setup menu On Screen menu Display from Remote ControlConvergence 1 Adjustment for RED, Blue and Green Convergence AdjustmentConvergence Adjustment mode Tuning Channels Channel Selection Tuning ChannelsReceive Channel Tuning Channels Channel AllocationChina HK/UK Catv5MHz 5.5MHz 5MHz 6.0MHz Press to store the Sound System Tuning Channels Automatic TuneHelpful Hint Tuning Channels Manual TuneWhen a station is found How to Cancel the Fine Tuning Programme Number Skip Tuning Channels Fine TuningNTSC3.58 NTSC4.43 Condition Tuning Channels How to Cancel the Skip Function5MHz5.5MHz 5MHz6.0MHz Sound System Condition Auto PAL SecamOwner ID Press to go back to watching TV Setup AdjustmentPicture Adjustment Mode Picture AdjustmentSecam Signal Helpful Hint N NormalizationBass Sound AdjustmentVOLUME, BASS, TREBLE, Balance VolumePress to switch between on and OFF Sound AdjustmentAspect Controls Mode Picture ExplanationMUL I PIP Multi ScreenMulti PIP PIPPicture and text Multi ScreenChannel Search Picture and text TV / Teletext modeList / TOP mode Current programmeHold Index Accessing sub pagesWhen in TOP operation Button Function Advanced Remote Control OperationStereo / Bilingual Sound Selection VCR / DVD controlDVD Advanced Remote Control Operation Manufacfurer settingVCR Symptoms Checks TroubleshootingCleaning Component Terminals SpecificationsDimensions W ⋅ H ⋅ D Operating ConditionsMade in China Customer’s Record