Panasonic SC-BTX70 manual Enjoying TV, etc. with this unit’s speakers, Adjusting the sound, Status

Enjoying TV, etc. with this unit’s speakers

You can enjoy TV broadcasts with this unit’s speakers.

Adjusting the sound

You can adjust the mode depending on the source or situation.

1 Press [SOUND] several times to select the mode.

≥You can also press [SOUND] and then [3, 4] to select the mode.

≥The selected effect will only be displayed on the main unit.

EXT-IN EXT-IN

SURROUNDSOUND

SURROUND SOUND

2While the selected mode is displayed

Press [2, 1] and select the desired setting.

For more detailed information on this operation, please refer to the “Changing the sound modes” section on page 15.

Making settings for digital audio input

Select to suit the type of audio from the OPTICAL IN terminals on the main unit.

STATUS

Preparation

OK

STATUS

≥Underlined items are the factory presets.

Available settings
Mode	Setting
DUAL:	(Only works with Dolby Dual Mono)
	– M1
	–M2
	– M1+M2 (stereo audio)
	≥If this is set to “M1” or to “M2”, the PCM FIX
	modes will automatically be set to “OFF”.
DRC:	– ON

Confirm the audio connection to the OPTICAL IN or AUX terminal on this unit (> 9 to 10).

Turn on the TV.

1Press [EXT-IN] several times to select “D-IN 1” (DIGITAL IN 1)*1, “D-IN 2” (DIGITAL IN 2)*2 or “AUX”*1.

This unit: Press [RADIO/EXT-IN].

≥D-IN 1 (DIGITAL IN 1)*1:

When connecting using OPTICAL 1(TV) terminal.

≥D-IN 2 (DIGITAL IN 2)*2:

When connecting using OPTICAL 2(STB) terminal.

≥AUX*1:

When connecting using AUX terminal.

*1 For connections with the TV.

*2 For connections with other devices.

≥When the system is connected to an HDAVI Control 2 or later-compatible TV via an HDMI cable, TV broadcast audio is output through the system speakers if the TV input is switched to TV tuner mode. See “Setting the TV audio for VIERA Link “HDAVI Control”” on page 26 for setting method.

≥Reduce the volume on the TV to its minimum, and then adjust the volume of this unit.

Enjoying TV and other devices sound from this unit’s speakers

You can enhance stereo sources with surround sound effect.

Press [SURROUND] several times to select the mode.

≥You can also press [SURROUND] and then [3, 4] to select the mode.

≥The selected effect will only be displayed on the main unit.

For more detailed information on this operation, please refer to the “Enjoying surround sound effects” section on page 15.

Recommended modes to enjoy TV audio: 2.1 ch mode

≥DOLBY VIRTUAL SPEAKER REFERENCE ≥DOLBY VIRTUAL SPEAKER WIDE

4.1ch/6.1 ch mode (> 40)

≥DOLBY PL II MOVIE ≥DOLBY PL II MUSIC ≥S.SURROUND

(Dynamic	Adjust for clarity even when the volume is low
Range	by compressing the range of the lowest sound	TV
Compression)	level and the highest sound level. Convenient
	for late night viewing. (Only works with Dolby
	Digital)
	– OFF
	The full dynamic range of the signal is
	reproduced.
PCM FIX:	– ON
	Select when receiving only PCM signals.
	– OFF
	Select when receiving Dolby Digital and PCM
	signals.
	≥When receiving true 5.1-channel surround
	sound, select “OFF”.
	≥If this is set to “ON”, the DUAL mode will
	automatically be set to “M1+M2”.
TV AUDIO*3:	–AUX
	Select when receiving analogue sound from
	the TV to the AUX terminal.
	– D-IN 1
	Select when receiving digital sound from the
	TV to the OPTICAL 1(TV) terminal.
CABLE/SAT	– SET
AUDIO*4, 5:	Select when setting the main unit to switch to
	“D-IN 2” when the input channel of a HDMI
	connected STB is selected on the TV (B 26,
	Setting the TV audio for VIERA Link “HDAVI
	Control”).
	– OFF
	Select to cancel this setting.

1Press [EXT-IN] several times to select “D-IN 1”

(DIGITAL IN 1) or “D-IN 2” (DIGITAL IN 2).

Main unit: Press [RADIO/EXT-IN].

2Press [STATUS] several times to select the mode.

≥You can also press [STATUS] and then [3, 4] to select the mode.

≥The digital audio input settings are to be set separately to each source, “D-IN 1” and “D-IN 2”.

≥The selected effect will only be displayed on the main unit.

3While the selected mode is displayed

Press [2, 1] and select the desired setting.

*3 When “D-IN 1” is selected.

*4 When “D-IN 2” is selected.

*5 The device connected to the OPTICAL 2(STB) terminal must be connected to the TV via an HDMI cable. If it is not connected via an HDMI cable, “NOT CONDITIONAL” is displayed on the main unit.

	≥Audio that is input through the OPTICAL DIGITAL IN
	or AUX terminals are not output from the HDMI
NOTE	terminal.	RQT9464

25