RF Output Channel
|
|
|
|
| If you need additional operating assistance after |
Owner’s Manual | reading this owner’s manual or to order replace- | ||||
ment accessories, please call | |||||
Video Cassette Recorder | TOLL FREE : | ||||
6240VE |
|
|
|
| or visit our web site at |
|
|
|
|
| |
|
|
|
|
| |
|
|
|
|
|
|
1. Before using your VCR
If channel 3 is already occupied for broadcasting,
1)Set your TV to channel 4.
2)Insert a
3)Press the PLAY button once.
4)After a few seconds, press the PLAY button on the VCR for 3 seconds.
•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.
•When a picture does not appear on the TV screen, repeat step [4].
5) Press the STOP button to stop playback.
HintHint
•The RF output channel may not change when you adjust tracking during playback. In this case, stop the playback, and start the playback again. After that, press the PLAY but- ton on the VCR for 3 seconds again.
|
|
|
|
|
| Basic VCR/TV Connection |
|
| Stereo TV Connection |
|
|
|
|
|
Cable Antenna
Signal
or
(Back of TV) |
Disconnect |
Cable Antenna
Signal
or
2 |
Connect
(Back of VCR) | You can use the AUDIO OUT jack and | |
VIDEO OUT jack on the back of the | ||
|
| (Back of TV) VCR if your TV has Audio/Video Input |
ANT |
| jacks. In this case, you need to set the |
IN | 3 | TV to external Line Input Mode. Please |
| ||
OUT | refer to your TV’s owner’s manual. | |
| Connect | (Back of TV) |
VIDEO AUDIO IN |
| ||
IN | L | R | ANT |
|
|
| IN |
|
| AUDIO |
|
|
| OUT IN | OUT |
VIDEO
Audio/Video Cables
(not supplied)
1 |
Connect
(Back of VCR)
RF Cable (supplied) | Front & Rear Terminals |
|
4 Plug the AC power cords of the VCR and TV into the AC outlets. | ||||
Hint for Cable Box or Satellite Box |
|
|
| |
Connection A | (Back of VCR) | Connection B |
| (Back of VCR) |
(Cable box or | ANT |
| ANT | (Cable box or |
Satellite box) |
| IN | ||
IN |
|
| ||
AUDIO OUT jack
Connect the audio cable to the audio in jack of a camcorder, another VCR, a stereo amplifier, or an audio system.
ANT
AUDIO IN jack
Connect the audio cable from the audio out jack of a camcorder, another VCR, or an audio source.
ANT | ANT IN jack |
IN | |
| Connect your antenna or cable box. |
IN | OUT |
|
|
| Cable | OUT | Satellite box) | |
| OUT | RF Cable | E | IN | E | |||
Cable |
|
|
| Signal |
| OUT | ||
|
|
|
|
| ||||
Signal |
|
| (supplied) |
|
|
|
| RF Cable (Back of TV) |
|
|
| (Back of TV) |
| RF Cable (supplied) |
| ||
AUDIO
OUT IN
VIDEO
IN
OUT
AUDIO
OUT IN
| ANT OUT jack |
OUT | Connect the RF cable (supplied) to |
|
Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the VCR. You can view or record ONLY the channels you have selected on the cable box or the satellite box.
•While you are recording, only the recorded channel can be viewed.
To select channels of the cable box or satellite box
1)Turn on the VCR by pressing the POWER button, and then, press the VCR/TV button.The POWER and the VCR/TV indicators on the front panel will light on. Then, press the CHANNEL buttons to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box).
•If you use the channel 4, you need to change the VCR’s RF output to channel 4. Refer to “RF Output Channel”.
Select this connection when you want to change channels on the VCR. With this connection, you may watch one channel while recording another.
• You may not view or record a scrambled channel.
To select channels of the cable box or satellite box
1)At the cable box or satellite box, select channel 3 or 4 (the same channel as the VCR’s RF output channel.)
• Refer to “RF Output Channel”.
2)At the TV, select the same channel as the output chan- nel (3 or 4) of the cable box or satellite box.
3)Turn on the VCR by pressing the POWER button, and then, press the VCR/TV button .The POWER and VCR/TV indicators on the front panel will light on. Then, select the channel you want to view or record.
To play back a tape
VIDEO
VIDEO OUT jack
Connect the video cable to the video in jack of a camcorder, another VCR, or a TV.
| POWER | CHANNEL |
|
|
| M |
VIDEO | AUDIO | POWER | VCR/TV | TAPE IN | TIMER | REC |
|
|
|
|
|
Supplied Accessory
• Remote control | • RF Cable | • Owner’s Manual |
(NA371UD) with | (WPZ0901TM002) | (0VMN03900) |
Two AA batteries |
|
|
the antenna input jack on your TV. |
VIDEO IN jack
Connect the video cable from the video out jack of a camcorder, another VCR, or an
Installing the Batteries for the Remote Control
Install two AA batteries (supplied) matching the polarity indicated on 
2)At the TV, select channel 3 or 4 (the same channel as you have selected at step 1).
3)At the cable box or satellite box, select the channel you want to view or record.
Follow the steps 1) to 2) above. Then, play back a tape.
• Refer to “Playback” on page 5.
To view one channel while recording another
1)While you are recording on the VCR, press the VCR/TV but- ton so that the VCR/TV indicator disappears on the VCR.
2)At the cable box or satellite box, select the channel you
want to view. | - 1 - |
|
the bottom of the remote control.
Printed in China
0VMN03900 / HF310UD ★★★★★