Panasonic TX-28PL4 manual VCR and Satellite Receiver Installation, To tune your TV to the VCR

Page 36

VCR AND SATELLITE RECEIVER INSTALLATION

Your new TV is supplied with programme position ‘0’ set to receive an RF signal from your VCR, although a Scart connection is preferable if the VCR is so equipped.

However, if for some reason your VCR is tuned to a different RF channel then you will not receive any picture or sound from your VCR on programme position ‘0’ of the TV. It will be necessary to either adjust the RF channel of your VCR (some VCR’s allow adjustment of their RF channel via their remote control unit) or to adjust the tuning of the TV’s programme position ‘0’ or both until it receives the RF output channel of your VCR.

It is intended that this advice is used in conjunction with the instruction books for your additional equipment. Use the AV1 Scart terminal for a VCR.

Use the AV2S Scart terminal for an S-- Video VCR.

Use the AV2S Scart terminal for a Q-- Link, NEXTVIEWLINK or compatible VCR.

To tune your TV to the VCR

Switch on the VCR, insert and play a pre-recorded tape with known content

SET UP

Open the Setup menu

Move to Tuning menu

Access Tuning menu

Move to Manual tuning

Setup menu

Teletext Off timer Tuning menu

Select

Access

TV/AV Exit

FASTEXT

Off

Access

Access Manual tuning

Select programme position ‘0’ VCR

Start searching for the VCR playback of the known content tape

STR

When the VCR playback is found, press STR to store

TV/AV

Press the TV/AV button to exit

See below for installation of VCR and Satellite Receiver

Notes :

DIf picture patterning occurs on programme position ‘0’ it may be necessary to adjust the RF output channel of the VCR, refer to the VCR instruction book.

DIf a Satellite Receiver and a VCR are going to be used with RF cable connections it is important to avoid both units being set on the same channel.

Refer to the Satellite Receiver and VCR instruction books for precise tuning information.

VCR

CH32

							Programme
							down/up
							Search
							Search
		Return --					down/up
							down/up
						TV/AV	Exit
						TV/AV	Exit
				’STR’ Button			Store

	Manual tuning

21							68

VCR

36

Image 36

Contents TX---28PL4 Contents WelcomeHow to replace the fuse for plug type shown in example Cabinet and Picture Tube CareAccessories Inserting the Remote Control BatteriesCheck that you have the accessories and items shown Basic Controls Front Panel and Remote Control Connection and setting up options Connection of TV using an RF cable onlyConnection of TV and VCR using Scart and RF cables Quick Start GuideWhat is Q-Link ? Link connection of TV and VCR using Scart and RF cablesScart Connection RF Connections Connect the speakers Rear Surround SpeakersGrey / Black GreyCentre speaker Position the speakersEnsure that the VCR is in Standby mode Owner IDEnter NAME, House Number and Postcode Number and Postcode are enteredTV to VCR Download Press and release here to open flap Using the on Screen Displays Instructions Indicator for optionsAspect Controls Panasonic AutoZoom Full 149Just Picture Menu Contrast Brightness Colour SharpnessTint Colour balance Volume Output volumeSound Menu Bass Treble BalanceSetup Menu Teletext Off timerVolume correc Tuning Menu overview Decoder AV2Tuning Menu Programme Edit To delete an unwanted programme positionChanges If you have finished Programme edit menu, press TV/AV button to exitTo add a programme position To move a programme to another positionTo rename a programme position Programme edit menu, pressTo lock a programme position to prevent access Lock Off Press STR to storeTuning Menu Auto Setup Tuning Menu Manual Tuning Manual tuning Front panelTuning Menu Shipping Condition Press STR to startTuning Menu Owner I.D Change character Select character positionAV Select and Setup Setup menuSound menu Preset Download LinkTV / VCR Auto Power On VCR Auto Power StandbyWhat You See Is What You Record Direct TV Recording VCR Image View OnVolume Surround mode Ensure that the Surround feature is switched OnPro Logic/Simulated setting Surround MenuPRO Logic Mode Dolby Pro Logic Normal Centre modeSimulated Mode Speaker Level SetupSetting Effect Appropriate sources VCR and Satellite Receiver Installation When the VCR playback is found, press STR to storeTo tune your TV to the VCR VCR / DVD Operation Teletext Operation Update Display Sub Coded Page AccessFavourite Page F.P IndexAudio / Video Connections Scart and S---Video socket informationRear AV1/AV2S 21 Pin Scart terminals Not Troubleshooting Symptoms ChecksSound Specifications For Your GuidancePage Page Page Sales and Support Information Customer Care Centre