Panasonic TX-28PL4 manual For Your Guidance, Specifications

Page 44

FOR YOUR GUIDANCE

HService

Before requesting service, please refer to the troubleshooting guide on previous page to determine the symptoms. To obtain service please contact your local Panasonic dealer quoting the model number and serial number (both are located at the rear of the TV).

H TV Games / Home Computers

Extended use of TV games or home computers with any television

set can cause a permanent ‘shadow’ on the screen. This type of irreversible picture tube damage, can be limited by observing the following points:

DReduce the brightness and contrast levels to a minimum viewing level.

DDo not operate the television set for a continuous period of time while using TV games or home computers.

DThis type of picture tube damage, is not an operating defect, and as such is not covered by the Panasonic warranty.

H Last Position Memory

Certain functions have a last position memory, i.e. the setting at the time of switch-- off will be the setting used when the receiver is

switched on again:--

 

Programme

Tint (M.NTSC / NTSC only)

Headphone volume

Volume correction (in AV mode only)

AV Position

Contrast

Volume

Sharpness

NICAM

Aspect mode

Bass

Standby

Treble

Artificial Intelligence (AI)

Balance

Colour

Colour Balance

Brightness

Status

P-- NR

Teletext mode

Decoder (AV2)

Surround mode

Speaker level setting

Speaker distance

Geomagnetic correction

H Sleep Feature

If the set is not switched off when the TV station stops transmitting , it will automatically go to standby mode after 30 minutes. This function will not operate when the TV is in AV mode.

SPECIFICATIONS

Power Source

Power Consumption

Standby Consumption

Picture Tube

Visible Diagonal

TX-28PL4

220 -- 240V 50Hz A.C.

98W

1.4W

66 cm

Audio Output

Music Power

Dimensions

Weight (Kg)

Receiving Systems/ Band name

H W D

 

Front Left / Right 20W x 2, Surround 15W x 2, 8Ω impedance

 

External Centre 20W, 6Ω impedance

 

508,8 mm

 

763,2 mm

 

512,2 mm

 

42

 

 

PAL I

UHF E21-- 68

PAL 525/60

Playback of NTSC tape from some PAL Video recorders (VCR)

M.NTSC

Playback from M.NTSC Videorecorders (VCR)

NTSC (AV input only) Playback from NTSC Videorecorders (VCR)

 

Aerial - Rear

 

UHF

 

 

 

 

 

Headphones - Front

 

3.5mm, 8Ω impedance

 

 

 

 

 

AV - Rear

 

AV1 -- 21 pin terminal -- Audio / Video in / out, RGB in

 

 

AV2 -- 21 pin terminal -- Audio / Video in/out, S-- Video in, Q-- Link

 

 

 

 

Dolby Surround Out

- Rear

5 x Dolby Surround Out RCA

 

External Speaker connections -- 2 x Rear, 1 x Centre

 

 

 

 

AV - Front

 

AV3 -- S ---Video in, RCA Audio / Video in

 

 

 

 

Specifications are subject to change without notice. Weight and dimensions shown are approximate.

Dolby, Pro Logic and the are trademarks of Dolby Laboratories. Manufactured under license from Dolby Laboratories.

44

Image 44
Contents TX---28PL4 Contents WelcomeHow to replace the fuse for plug type shown in example Cabinet and Picture Tube CareCheck that you have the accessories and items shown AccessoriesInserting the Remote Control Batteries Basic Controls Front Panel and Remote Control Connection and setting up options Connection of TV using an RF cable onlyConnection of TV and VCR using Scart and RF cables Quick Start GuideScart Connection What is Q-Link ?Link connection of TV and VCR using Scart and RF cables RF Connections Connect the speakers Rear Surround SpeakersGrey / Black GreyCentre speaker Position the speakersEnsure that the VCR is in Standby mode Owner IDEnter NAME, House Number and Postcode Number and Postcode are enteredTV to VCR Download Press and release here to open flap Using the on Screen Displays Instructions Indicator for optionsAspect Controls Panasonic AutoZoom Just Full149 Tint Colour balance Picture MenuContrast Brightness Colour Sharpness Volume Output volumeSound Menu Bass Treble BalanceVolume correc Setup MenuTeletext Off timer Tuning Menu overview Decoder AV2Tuning Menu Programme Edit To delete an unwanted programme positionChanges If you have finished Programme edit menu, press TV/AV button to exitTo add a programme position To move a programme to another positionTo rename a programme position Programme edit menu, pressTo lock a programme position to prevent access Lock Off Press STR to storeTuning Menu Auto Setup Tuning Menu Manual Tuning Manual tuning Front panelTuning Menu Shipping Condition Press STR to startTuning Menu Owner I.D Change character Select character positionSound menu AV Select and SetupSetup menu Preset Download LinkTV / VCR Auto Power On VCR Auto Power StandbyWhat You See Is What You Record Direct TV Recording VCR Image View OnVolume Surround mode Ensure that the Surround feature is switched OnPro Logic/Simulated setting Surround MenuPRO Logic Mode Dolby Pro Logic Normal Centre modeSetting Effect Appropriate sources Simulated ModeSpeaker Level Setup To tune your TV to the VCR VCR and Satellite Receiver InstallationWhen the VCR playback is found, press STR to store VCR / DVD Operation Teletext Operation Update Display Sub Coded Page AccessFavourite Page F.P IndexAudio / Video Connections Scart and S---Video socket informationRear AV1/AV2S 21 Pin Scart terminals Not Sound TroubleshootingSymptoms Checks Specifications For Your GuidancePage Page Page Sales and Support Information Customer Care Centre