Operation
Setting Up Your Remote Control
After it has been set up properly, your remote control can operate in six different modes:
TV, VCR, CABLE, DVD, SETBOX or AUDIO. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose.
Note
The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.
Controller Operation
To control a device using the Controller
1.Program the Controller to work with your device.
2.Changing device mode by pressing the SELECT key. Default device is TV. When press SELECT key, current device led will be on. Keep pressing SELECT key to choose a device, the loop is: TV DVD VCR STB Cable Audio - TV. When device is set, related device LED will be on for 5 seconds and then be off.
3.Aim the remote at the device.
4.Press the POWER button to turn the device on.
5.Use the other Controller buttons to operate the device. Device LED will blink if user presses any key (if the key has data in current mode.). If the key has no data, then LED will not blink.
6.Default init status: TV/Haier 001 code.
7.Bulb key to control the flash light.
Programming the Controller
The Controller is
Selecting a brand code for the device you wish to operate, and then entering that code manually into the Controller.
Using the Power Scan feature to find device codes automatically. The two programming methods are described in the following sections.
Manually Programming the Controller
1.Using SELECT key to choose the device you want to program.
2.While Press and holding OK key, press SELECT key, and device LED will be ON. Keep the status for about 5 seconds, release both keys and then LED will blink twice per second, indicating that the Controller is ready for programming.
3.Led will blink once when you enter a digit key, indicating the digit key is programmed. If 3 digits are programmed successfully, device LED will be ON for about 3 seconds and then blink twice per second. Then User now can:
a)Try to operate the device by using POWER or PLAY keys. If operation can be done, press OK to save current
b)Return to beginning of step 3. Reprogram the controller.
5.If user's input is incorrect, LED will blink 12 times in 3 seconds. And then keep twice per second blink, user now can return to step 3 and
6.Within 10 seconds, user should enter the
out or any key other than POWER
PLAY and digits is pressed, LED will be off and manually programming process is exit.
7.Fast Programming Haier default TV code set. Press and holding the EXIT key and then press SELECT key for 5 seconds, default Haier code set (001) will be programmed to the controller.
Manually scan mode
With manually scan programming, the Controller tests all the codes available in the code set data base and assign the correct one for the selected device.
To
1.Manually turn OFF the device for manually scan mode. (TV, VCR, DVD, STB, cable box or audio equipment).
2.Press SELECT key to choose the device you wish to program.
While Press and holding OK key, press the SELECT key and device LED will be ON. Keep the status for about 5 seconds, release both keys and then LED will blink twice per second, indicating that the Controller is ready for programming.
3.Press and release the CH+/CH- key. The LED blinks 10 times per seconds, indicating that the Remote is in manually scan mode.
4.Press CH+/CH- key repeatedly until the device switches ON (CH+ key conducts a upward search while the CH- key conducts a downward search in the code set database).
5.When the device turns ON, press and release the OK key to program the Controller with the new code, saving the code and exit. To exit without programming, press any key other except CH+/CH- and OK. LED will be off after manually scan mode is exit.
6.If the device responds, no further programming is required. If the device does not respond, repeat step 1 through 5.And searching will start from current code set. If no key was pressed in 30 seconds, manually scan mode will be automatically exit.
7.After searching the entire data base, this mode will be automatically exited and led will blink for 3 times.
Owner
s Manual 31