Symphonic SF225B Initial SET UP for USE, Setting the CH3/CH4 Switch, Automatic Channel SET UP

CH3 CH4

[Back of the VCR]

OUT

CH3 CH4

INITIAL SET UP FOR USE

SETTING THE CH3/CH4

SWITCH

If your TV does not have A/V terminals:

When the VCR is in the Playback mode or when the VCR is in the VCR position, your TV will receive sig- nals from the VCR on either channel 3 or 4.

To use the VCR with your TV, set the selector switch to CH3 or CH4 (which is located

5Begin channel preset

by pressing the B button once. The tuner scans and memorizes all active channels in your area.

●The VCR distinguishes be- tween standard TV channels and cable channels.

CH 01

AUTO SET UP

in the back of your VCR), whichever is not used for nor- mal broadcasts in your area. Then set your TV to the same channel.

6After scanning, the tuner stops on the lowest memorized channel. The TV screen returns to TV mode.

●If "AUTO SET UP" appears on the TV screen again, check the cable connections. Press the Bbutton once again and the VCR will begin preset again.

AUTOMATIC CHANNEL SET UP

You can automatically program the tuner to scan only the channels you receive in your area.

●Channel memory programming is NOT needed when you connected the VCR to a cable box or satellite box as in "Basic connections" on page 6. In this case, select the VCR and TV to channel 3 or 4 the same channel as the CH3 or CH4 switch on the back of the VCR. Then, the channel you want to re- cord or view may be selected at the cable box or sat- ellite box.

●Follow the steps below once. Repeat it only if there is a power failure or if the VCR is unplugged for more than 30 seconds. (In these cases, the programmed channels are erased.)

●You must follow the steps below before attempting to play or record a video tape. If you want to play or record a video tape BEFORE programming the tuner, you can cancel it by pressing the RESET/EXIT but- ton. To program the tuner again, see "CHANNEL SET UP AGAIN" on the next page.

1You need to connect antenna/cable to the VCR first. Then, connect the VCR power plug into a standard AC outlet.

2Turn on the TV and set the TV to channel 3 or 4.

Now set the CH3/CH4 switch on the back of the VCR to match the channel selected on the TV.

3Turn on the VCR by pressing the POWER button. Both the PWR. indicator and the VCR indicator on the VCR come on.

4 Select the On Screen Lan-		LANGUAGE SELECT
guage	("ENGLISH" or	————————————————
"ESPAÑ OL") by pressing		B ENGLISH [ON]
the ▲ or	▼ button. Then,	ESPAÑ OL
press the B button.

TO SELECT A DESIRED CHANNEL

You can select the desired channel by using the CHAN- NEL Up or Down button or directly pressing the number buttons on the remote control.

Note for using the number buttons:

●When selecting cable channels which are higher than 99, press the +100 button first, then press the last two digits.

●You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).

CLOCK SET UP

Set the clock accurately for proper automatic timer re- cording. We suggest that you use a TV or radio station as your time source.

1Select main menu by pressing the MENU button. (If the clock is not set, the CLOCK SET menu ap- pears first. In this case, follow step [3].)

2Select "CLOCK SET" by pressing the ▲ or ▼ but- ton. Then, press the B button.

3Set the clock.

Set the month	Press the ▲ or ▼ button repeatedly.
	Then, press the B button.
Set the day	Press the ▲ or ▼ button repeatedly.
	Then, press the B button.
Set the year	Press the ▲ or ▼ button repeatedly.
	Then, press the B button.
	The day of the week will appear automatically.
	Press the ▲ or ▼ button repeatedly.
Set the hour
	Then, press the B button.
	Press the ▲ or ▼ button repeatedly.
Set the minute
	Then, press the B button.		CLOCK SET
	Press the ▲ or ▼ button
Set the AM or PM
	repeatedly.	MONTH		DAY	YEAR
		03	/	19 MON	2001
		HOUR		MINUTE	AM/PM
		05	:	40	PM AM
					PM

●To go back one step, press the s button.

4Start the clock by pressing the RESET/EXIT or B button after setting the AM or PM.

- 7 - EN

0J11