Sharp LC-65E77UM Preparation, Antennas, Installing Batteries in the Remote Control Unit

Page 10

Preparation

Antennas

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, plug it into the antenna terminal at the rear of the TV set.

1.A 75-ohm system is generally a round cable with F-type connector that can easily be attached to a terminal without tools (Commercially available).

2.A 300-ohm system is a fl at “twin-lead” cable that can be attached to a 75-ohm terminal through a 300/75-ohm adapter (Commercially available).

F-type connector

75-ohm coaxial cable (round)

300-ohm twin-lead cable (fl at)

NOTICE F-type connector should be finger-tightened only.

When connecting the RF cable to the TV set, do not tighten F-type connector with tools.

If tools are used, it may cause damage to your TV set. (The breaking of internal circuit, etc.)

F-type connector

75-ohm coaxial cable

Connecting Antenna Cable

Connect the antenna cable to the TV using one of the methods in the illustration as shown (1, 2, 3 or 4).

1Cable without a CATV converter

2VHF/UHF antenna

3Combination VHF/ UHF antenna

4Separate VHF/UHF antenna

 

Home Antenna

Cable TV lead-In

terminal (75-ohm)

 

 

Coaxial cable

 

(commercially available)

 

Home Antenna

75-ohm coaxial cable (round)

terminal (75-ohm)

 

 

Coaxial cable

 

(commercially available)

75-ohm coaxial cable (round)

 

 

or

 

300/75-ohm adapter

300-ohm twin-lead cable (flat)

(commercially available)

 

VHF

UHF

300-ohm

 

 

ANTENNA

ANTENNA

 

 

twin-lead cable

 

 

 

 

 

 

 

 

 

IN

OUT

 

300-ohm twin-lead cable

Combiner

 

 

 

 

 

or

 

 

(commercially available)

75-ohm coaxial cable

 

 

 

 

 

To TV antenna terminal

Installing Batteries in the Remote Control Unit

If the remote control fails to operate TV functions, replace the batteries in the remote control unit.

1Open the battery cover.

2Insert two “AAA” size batteries (supplied with the product).

3Close the battery cover.

Place the batteries with their terminals corresponding to the (e) and (f) indications in the battery compartment.

CAUTION

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

Do not mix batteries of different types. Different types of batteries have different characteristics.

Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries.

Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a rash. If you fi nd any chemical leakage, wipe thoroughly with a cloth.

The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

If you will not be using the remote control unit for an extended period of time, remove batteries from it.

8

Image 10
Contents LC-60E77UN LC-65E77UM Page LC-60E77UN LC-65E77UM Trademarks Declaration of ConformityAdditional Safety Information Dear Sharp CustomerPrecautions when transporting the TV Caring for the CabinetChild Safety Caring for the Liquid Crystal panelContents Supplied AccessoriesUsing the Remote Control Unit Power indicator on the front of the television lights GreenClose the battery cover Installing Batteries in the Remote Control UnitConnecting Antenna Cable PreparationPart Names TV Front TV Rear/SideRemote Control Unit When using the remote control unit, point it at the TVWhen using Hdmi cable Input 5, 6, 7 or Connecting to External EquipmentWhen using HDMI-DVI conversion cable Input Rear of the TV When using S-VIDEO cable Input Rear of the TV When using Component cable Input 1 or Rear of the TVGame console Camcorder When using optical fiber cable Rear of the TV Connecting a Speaker/AmplifierConnecting a PC When using audio cable Rear of the TVWhen using analog RGB cable Rear of the TV When using RS-232C serial control cable Rear of the TVInitial Setup Turning On/Off the PowerWatching TV Direct Button Operation Changing VolumeSleep Timer Changing ChannelsMTS/SAP stereo mode Digital broadcasting audio modeClosed Captions and Digital Closed Captions Press Power SavingExamples For 43 programs Press View ModeYou can select the screen size For HD programsOn-Screen Display Menu Using the remote controlUsing the control panel of the main unit On-Screen Display Menu OperationMenu Items Color Temp Color Temperature OPC SettingAdvanced Picture Setting Picture MenuFine Motion Enhanced Gamma AdjustmentFilm Mode 32 pull-down Active ContrastPower Control Menu Audio MenuSetup Menu Position Parental Ctrl Parental Control SettingReset LanguageMpaa Voluntary movie rating system When setting an individual content-based rating itemChip TV Parental GuidelinesCanadian French Ratings How to temporarily release the V-CHIP BlockCanadian English Ratings Reactivating the temporarily released V-CHIP BlockOption Menu Demo Mode Caption SetupFavorite CH Favorite Channel Setting Color System Operation Lock OutSoftware Update Digital Setup MenuAudio Setup IdentificationAfter the screen shown below is displayed, press During the data checking, Checking blinksPress Enter to start updating Remove the USB memory device9CBL/SAT, DOT SAT Presetting Remote Control FunctionOther Viewing Options 14 a/b/c/d, EnterOther Viewing Options Manufacturer codes Using Aquos Link Controlling Hdmi Equipment Using Aquos LinkOne Touch Recording Aquos Link SetupAuto Power On Selecting RecorderOne Touch Playback Timer RecordingAquos Link Menu Press d to start playing back a titleSelecting Media Type for Aquos Link Compatible Recorder Playback of Titles Using Aquos LinkManually Changing Aquos Audio Speaker System’s Sound Mode Hdmi Device SelectionDisplaying a PC Image on the Screen Stretch Dot by DotAuto Sync For Analog PC Input Mode Only Adjusting the PC Image Setting Audio InputPC Compatibility Chart PC Audio SelectCommands not indicated here are not guaranteed to operate RS-232C Port SpecificationsAppendix Setting the TV on the WallRemoving the Stand Troubleshooting Pages 22Troubleshooting-Digital Broadcasting Error message about reception of broadcastModel LC-60E77UN Model LC-65E77UM Optional AccessorySpecifications Part nameSoftware developed by Sharp and open source software Information on the Software License for This ProductSoftware composition Obtaining source codeCalling for Service Limited WarrantyAN-52AG4 Dimensional DrawingsAN-65AG1 Sharp Electronics Corporation