Sharp LC-50LE762EN, LC-50LE761E, LC-50LE760E manual Using a Conditional Access Module, Shut Down?

Page 12

Using a Conditional Access Module

IMPORTANT: Insert or remove the CI module only when the TV is SWITCHED OFF.

In order to watch certain digital channels, a conditional access module (CAM) can be necessary. This module must be inserted in the CI slot of your TV.

1.Obtain the Conditional Access Module (CAM) and the viewing card by subscribing to a pay channel company, then insert those to the TV using the following procedure.

2.Insert the CAM and then the viewing card to the slot that is located in the terminal cover at the rear side of the TV.

3.The CAM should be correctly inserted, it is impossible to insert fully if reversed. The CAM or the TV terminal may be damaged if the CAM is forcefully inserted.

4.Connect the TV to the mains supply, switch on and then wait for few moments until the card is activated.

5.When no module is inserted, “No Common Interface module detected” message appears on the screen.

You can refer to the module instruction manual for details of the settings.

Note: It takes a few minutes to certify the licence key when you insert a CA card into the CI+ compatible CI module for the first time. This process may fail when there is no antenna input or you have never run “Auto installation”. If the old CAM is used, authentication may fail. In such cases, contact the contracted service provider.

CAM module

English

Standby Notifications

If the TV does not receive any input signal (e.g. from an aerial or HDMI source) for 5 minutes, the TV will go into standby. When you next switch-on, the following message will be displayed:

“TV switched to stand-by mode automatically because there was no signal for a long time.”

Press OK to continue.

If the TV has been left on and not been operated for a while, the TV will go into standby. When you next switch-on, the following message will be displayed:

“TV switched to stand-by mode automatically because no operation was made for a long time.”

Press OK to continue.

When the Auto TV OFF timeout is reached, the following message will be displayed on the screen:

“Shut Down?”

Select Yes to shut down the TV. Select No to cancel. The TV will switch off as well, if you do not make a

selection on this screen.

- 11 -

Image 12
Contents Page Contents TV Features Blue Neutral Brown LiveEnglish Important safety precautions Dear Sharp customerPower Source Power CordCleaning Moisture and WaterReplacement Parts Disconnecting the DeviceHeadphone Volume InstallationEnvironmental Information Electrical device not in the hands of childrenRepair Information Package Contents Connect PowerInstalling The Batteries Into The Remote TV Control button & OperationSwitching On/Off To Switch the TV OnTo Switch the TV to Standby To Switch the TV OffViewing remote control TV Using My buttonEnglish Using My Button Viewing the Connections VGAUsing a Conditional Access Module Shut Down?First Time Installation Media Playback via USB InputUsing the Channel List Changing Image Size Picture FormatsQuick Menu CEC and CEC RC PassthroughMenu Features and Functions Picture Menu ContentsAdvanced Settings Sound Menu Contents Settings Menu ContentsOther Settings Displays other setting options of the TV set Install and Retune Menu Contents Electronic Programme Guide EPG Recording a ProgrammeProgramme Options Digital Teletext for UK onlyRecording Configuration Timeshift RecordingInstant Recording Watching Recorded ProgrammesConfiguring Network Settings Connecting to your mobile device via WiFiUsing Miracast Information On Menu ItemsUsing Dlna Network Service Internet PortalNetflix Connectivity Troubleshooting Wireless Network Not AvailableHbbtv System Precautions Connection is SlowDistruption during playback or slow reactions Operating the 3D Mode 3D SettingsHealth Warning! 3D Images 3D Viewing InformationSoftware Upgrade Software upgrade search via user interfaceHorizontal Viewing Angle Vertical Viewing Angle Viewing DistanceTroubleshooting & Tips Internet Connection Not Available / Dlna Mode Not Operating Invalid DomainTV sometimes makes a cracking sound Miracast image/audio cannot be output to the TVAV and Hdmi Signal Compatibility Input Signal Types PC Typical Display ModesEnglish Not Available, O Available Supported File Formats for USB Media Browser Extension FormatSupported DVI Resolutions Supported File Formats for by MKVSpecifications Wireless LAN Specifications Frequency RangeLicence Notifications Disclaimers for services using the Internet EC Declaration of ConformityNero MediaHome Installation To install Nero MediaHome, please proceed as followsEnd of life disposal Dimensional Drawings 42240 50240Installing the Stand Installing the StandUninstalling the Stand Uninstalling the StandScrew Dimensions Wall Mounting Length