Sharp LC-40D78UN Preparation, Antennas, Installing Batteries in the Remote Control Unit

Page 9
Preparation

Preparation

Antennas

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, plug it into the antenna terminal at the rear of the TV set.

1.A 75-ohm system is generally a round cable with F-type connector that can easily be attached to a terminal without tools (Commercially available).

2.A 300-ohm system is a fl at “twin-lead” cable that can be attached to a 75-ohm terminal through a 300/75-ohm adapter (Commercially available).

AntennasF-type connector

75-ohm coaxial cable (round)

300-ohm twin-lead cable (fl at)

NOTICE F-type connector should be finger-tightened only.

When connecting the RF cable to the TV set, do not tighten F-type connector with tools.

If tools are used, it may cause damage to your TV set. (The breaking of internal circuit, etc.)

Connecting Antenna Cable

F-type connector

75-ohm coaxial cable

•Connect the antenna cable to the TV using one of the methods in the illustration as shown (1, 2, 3 or 4).

1Cable without a CATV converter

2VHF/UHF antenna

3Combination VHF/ UHF antenna

Cable TV lead-In

75-ohm coaxial cable (round)

75-ohm coaxial cable (round)

Home Antenna terminal (75-ohm)

Coaxial cable (commercially available)

Home Antenna terminal (75-ohm)

Coaxial cable (commercially available)

 

or

300/75-ohm adapter

300-ohm twin-lead cable (flat)

 

(commercially available)

 

 

 

 

 

 

 

4 Separate VHF/UHF

 

UHF

300-ohm

VHF

ANTENNA

antenna

twin-lead cable

 

 

ANTENNA

 

300-ohm twin-lead cable

or 75-ohm coaxial cable

IN OUT NOTICE F-type connector should be finger-tightened only.Connecting Antenna CableInstalling Batteries in the Remote Control UnitManual background

Combiner (commercially available)

To TV antenna terminal

Installing Batteries in the Remote Control Unit

If the remote control fails to operate TV functions, replace the batteries in the remote control unit.

1 Open the battery cover.

2 Insert two “AA” size batteries

3 Close the battery cover.

 

(supplied with the product).

 

•Place the batteries with their terminals corresponding to the (e) and (f) indications in the battery compartment.

CAUTION

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

•Do not mix batteries of different types. Different types of batteries have different characteristics.

•Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries.

•Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a rash. If you fi nd any chemical leakage, wipe thoroughly with a cloth.

•The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

•If you will not be using the remote control unit for an extended period of time, remove batteries from it.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Make sure the following accessories are provided with the product Supplied AccessoriesLC-40D78UN OPERATION MANUALDECLARATION OF CONFORMITY IMPORTANT INFORMATION10P05-MX-NM Model No Serial NoFor U.S.A. only Sharp at 1-800-BE-SHARPINFORMATION IMPORTANT INFORMATIONIMPORTANT SAFETY INSTRUCTIONS Additional Safety InformationDEAR SHARP CUSTOMER Caring for the Cabinet Precautions when transporting the TVTHE ISSUE It Makes A Difference How and Where You Use Your Flat Panel DisplayTUNE INTO SAFETY Caring for the Liquid Crystal panelUsing an optional bracket to mount the TV Setting the TV on the WallQUICK REFERENCE Attaching/Detaching the StandUsing the Remote Control Unit QUICK INSTALLATION TIPS4 How to turn on the television for the fi rst time A Press POWER on the televisionNOTICE F-type connector should be finger-tightened only Installing Batteries in the Remote Control UnitConnecting Antenna Cable PreparationPOWER button MENU button INPUT button INPUT 5 terminal HDMI SERVICEPart Names TV FrontConnecting to External Equipment Connecting an Audio AmplifierConnecting a PC Initial Installation Turning On/Off the PowerWatching TV ENTERPOWER Changing VolumeYou can select 4 preset favorite channels in 4 different categories Sleep TimerExample When the input source is TV, INPUT 1, 2 or 3 terminals Allows you to gain quick access to PC mode. Press PCExample When the input source is INPUT 4, 5, 6 or 7 terminals You can enjoy Hi-Fi stereo sound or SAP broadcasts where available1 Press INPUT ⑬ INPUT1 Press CC 2 Press INPUT again or press a/b to select the input sourceVIEW MODE Input signalYou can select the screen size 1 Press VIEW MODEUse the following buttons on the remote control to operate the menu Using the remote controlUsing the control panel of the main unit MENU MENU on the remote control INPUT ENTER on the remote controlAdvanced Picture Setting OPC SettingPicture Menu On-Screen Display MenuPower control setting allows you to save energy Power Control MenuPower Saving No Signal OffEZ Setup Setup MenuYou can run EZ Setup again, even after setting up the preset channels For adjusting a pictures horizontal and vertical positionAudio Setup For automatically adjusting the PC imageReset 1 Return to factory pre-setting displays on the screenThree conditions must be met to enable the V-Chip see pages 22 to Parental CTRL Parental Control SettingYou can set and change the secret number by using Secret NoTV Parental Guidelines When setting an individual content-based rating itemCanadian English Ratings RatingCanadian French Ratings Option MenuReactivating the temporarily released V-CHIP BLOCK Audio OnlyFavorite CH Favorite Channel Setting Digital Caption SetupSoftware Update Operation Lock Out5 Press ENTER to start checking the data in the USB memory device 4 Input the 4-digit secret number by usingPress ENTER to start updating 6 During the data checking, “Checking” blinksProblem TroubleshootingPossible Solution No powerThe example of an error message Troubleshooting - Error MessageAppendix No pictureSpecifications Optional AccessoryModel LC-40D78UN Part namePC Compatibility Chart CLEARING THE SECRET NUMBERThe secret number is LIMITED WARRANTY Calling for ServiceCONSUMER LIMITED WARRANTY Warranty Period for this Product Additional Exclusions from
Top Page Image Contents