Sharp LC-32LE530E Using Side AV Connectors, Remote Control Handset, Switching On/Off

Page 14

Using Side AV Connectors

You can connect a range of optional equipment to your LCD TV using side connectors of the TV.

For connecting a camcorder or camera , you should use AV socket (side). To do this, you must use the supplied video/audio connection cable. First, plug single jack of the cable to the TV’s AV IN socket (side). Afterwards, insert your camera cable’s (not supplied) connectors into the plural part of the video/ audio connection cable. Colours of the connected jacks should match. See illustration below.

Afterwards, you should switch to Side AV source. See the section Input selection in the following sections for more information.

AV Connection

AV Cable

Cable (supplied)

(not supplied)

Remote Control Handset

Inserting Batteries

Remove the battery cover located on the back of the handset by gently pulling backwards from the indicated part.

Insert two AAA/R3 or equivalent type batteries inside. Observe the correct polarity (+/-) when inserting batteries and replace the battery cover.

Note: Remove the battery from remote control

SIDE AV

Headphone

Camera

handset when it is not to be used for a long period. Otherwise it can be damaged due to any leakage of batteries. Remote range is approximately 7m/23ft.

Switching On/Off

To listen the TV sound from headphones, you should connect headphones to your TV by using the HEADPHONE jack as illustrated above.

Using Other Connectors

You can connect a range of optional equipment to your LED TV. Possible connections are shown below. Note that cables shown in the illustration are not supplied.

For connecting a to a device that has SPDIF support, use an appropriate SPDIF cable to enable sound connection.

External Speakers

A device that

supports

SPDIF signal.

To Switch the TV On

Connect the power cord to the 220-240V AC 50 Hz.

Switch the “” button on the bottom right hand side under the screen to position “” so the TV will switch to standby mode. Then the standby LED lights up.

To switch on the TV from standby mode either:

Press the “” button, CH / CH or a numeric button on the remote control.

Press the “” or +/- button on the TV.

The TV will then switch on.

Note: If you switch on your TV via CH / CH buttons on the remote control or on the TV set, the programme that you were watching last will be reselected.

By either method the TV will switch on.

To Switch the TV to Standby

To switch the TV to low power stand by press the

” button on the remote control or right hand side of the TV.

Note: When the TV is switched to standby mode, standby LED can blink to indicate that features such as Standby Search, Over Air Download or Timer is active.

To Switch the TV Off

Switch the “” button on the bottom right hand side under the screen to position 2 as illustrated,

to isolate the TV from the mains, the LED will go out.

English - 13 -

A01_MB61_[GB]_1910UK_IDTV_TC_PVR_BRONZE16_32942LED_100Hz

_

ROCKER_10072539_50185773.indd 13

21.07.2011 14:30:17

 

 

 

 

Image 14
Contents LC-32LE530E Contents Blue Neutral Brown Live EnglishIntroduction FeaturesDear Sharp customer PreparationImportant safety precautions Precautions when transporting the TVSafety Precautions Electrical device not in the hands of children LCD ScreenLicence Notification Package Contents Remote Control Buttons Front and Rear View Control buttons View Viewing the Connections Back ConnectorsLCD TV and Operating Buttons Aerial Connection Viewing the Connections Side ConnectorsPower Connection Hdmi 1 Hdmi InputUSB Disk Connection Using USB InputsUSB Connection Programme RecordingConnecting to a DVD Player Connecting the LED TV to a PCSwitching On/Off Using Side AV ConnectorsRemote Control Handset Using Other ConnectorsViewing Electronic Programme Guide EPG Input SelectionBasic Operations Programme Options Record / Delete Record TimerRecording via EPG Screen Select ChannelFirst Time Installation Set Timer / Delete TimerAuto Channel Scan Retune Menu Operation InstallationManual Tuning Digital Aerial Manual SearchAnalogue Manual Search Clear Service ListDigital Cable Manual Search Analogue Fine TuneManaging Stations Channel List Managing Stations Sorting Channel List Media Playback Using Media BrowserManaging Stations Favourites On-Screen InformationSlideshow Options Viewing Videos via USBViewing Photos via USB Play This OK button Plays the selected file Up/Down NavigateRecordings Library Media Browser SettingsPlaying Music via USB Watching Recorded Programmes Timeshift RecordingInstant Recording Changing Image Size Picture Formats Picture Settings Menu Items Configuring Picture SettingsOperating Picture Settings Menu Items PanoramicOperating Sound Settings Menu Items Configuring Sound SettingsPC Picture Settings Sound Settings Menu ItemsOperating Settings Menu Items Using a Conditional Access ModuleConfiguring Your TV’s Settings Settings Menu ItemsParental Control Language SettingsConfiguring Language Preferences PreferredTimers Recording Configuration Configuring Date/Time SettingsConfiguring Source Settings Broadcast Type optional Configuring Other SettingsOperation Standby Search optionalColoured Buttons RED/GREEN/YELLOW/ Blue Other FeaturesTeletext Teletext function buttons are listed belowTips Appendix a PC Input Typical Display Modes Not Available, O AvailableSupported Players Stream Appendix C Supported DVI ResolutionsAppendix D Supported File Formats for USB Mode Audio Decoder MsadSoftware upgrade search via user interface BatteryAppendix E Software Upgrade AM search and upgrade modeDigital Reception DVB-C Digital Reception DVB-TSpecifications Transmission StandardsDimensional Drawings End of life disposal Detachable Stand Uninstallation Method Screw Dimensions