Sharp LC-80LE632U Adjusting the PC Image, Setting Audio Input, PC Compatibility Chart, Using a PC

Using a PC

Example

System Menu

Options

System Options

View Option

AQUOS LINK Setup

Input Terminal Setting

Menu Design

1Press MENU to display the MENU screen, and then press c/d to select "System Options".

2Press a/b to select "Input Terminal Setting", and then press ENTER.

3Press a/b to select "PC input" or "Audio Select", and then press ENTER.

4Press a/b to select a specifi c adjustment item, and then press ENTER to set each item.

5Press a/b (or c/d) to select or adjust the desired setting, and then press ENTER.

Adjusting the PC Image

Auto Sync. (for Analog PC Input Mode Only)

For automatically adjusting the PC image.

Yes: Auto Sync. starts and "Now adjusting the image." displays.

No: This function does not work.

•When "Auto Sync." is successful, "Completed" displays. If not, "Auto Sync." failed.

•"Auto Sync." may fail even if "Completed" displays.

•"Auto Sync." may fail if the computer image has low resolution, has unclear (black) edges, or is moved while executing "Auto Sync.".

•Be sure to connect the PC to the TV and switch it on before starting "Auto Sync.".

Fine Sync.

Ordinarily you can easily adjust the picture as necessary to change image position using "Auto Sync.". In some cases, however, manual adjustment is needed to optimize the image.

H-Pos.:Centers the image by moving it to the left or right.

V-Pos.:Centers the image by moving it up or down.

Clock: Adjust when the image fl ickers with vertical stripes.

Phase: Adjust when characters have low contrast or when the image fl ickers.

•For resetting all "Fine Sync." adjustment items to the factory preset values, press a/b to select "Reset", and then press

ENTER.

•It is not necessary to adjust the "Clock" or "Phase" when a digital signal is being input, so it cannot be selected.

•The default cursor position may not be in the center, because the screen position variable ranges may be asymmetrical.

•The screen position variable ranges depend on the View Mode or the signal type. The ranges can be seen on the position-setting screen.

Setting Audio Input

Audio Select

This function sets the terminal to output the computer audio.

The adjustment items vary depending on the input source. Select the input source corresponding to the terminal connected to the PC and then adjust the desired item.

■PC IN

Video: Select this when the TV and PC are connected using an analog RGB cable and the audio is not input.

Video+Audio: Select this when the TV and PC are connected using an analog RGB cable and the audio is input via a Ø 3.5 mm stereo minijack.

■HDMI 1

HDMI(Digital): Select this when the TV and PC are connected using an HDMI-certifi ed cable and audio is input via the same cable.

HDMI+Analog: Select this when the TV and PC are connected using a DVI-HDMI conversion cable and the audio is input via a Ø 3.5 mm stereo minijack.

•When "Audio Select" is set to "HDMI(Digital)", sound will not be produced if you use only an HDMI-certifi ed cable to connect HDMI-compatible equipment. To produce sound, you should make an analog audio connection.

•If you want to connect HDMI-compatible equipment using only an HDMI-certifi ed cable, set "Audio Select" to "HDMI(Digital)".

PC Compatibility Chart

It is necessary to set the PC correctly to display XGA and WXGA signal.

Resolution		Horizontal	Vertical		VESA
		Frequency	Frequency	Standard
	720 x 400	31.5 kHz	70 Hz
VGA		31.5 kHz	60 Hz		O
	640 x 480	37.9 kHz	72 Hz		O
		37.5 kHz	75 Hz		O
		35.1 kHz	56 Hz		O
SVGA	800 x 600	37.9 kHz	60 Hz		O
		48.1 kHz	72 Hz		O
		46.9 kHz	75 Hz		O
XGA	1024 x 768	48.4 kHz	60 Hz		O
		56.5 kHz	70 Hz		O
		60.0 kHz	75 Hz		O
WXGA	1360 x 768	47.7 kHz	60 Hz		O
SXGA	1280 x 1024	64.0 kHz	60 Hz		O
SXGA+	1400 x 1050	65.3 kHz	60 Hz		O
UXGA	1600 x 1200	75.0 kHz	60 Hz		O
1080p	1920 x 1080	67.5 kHz	60 Hz

VGA and XGA are registered trademarks of International Business Machines Corp.

57