Sharp LC-80LE632U operation manual Control of the TV

Page 60

Using a PC

Control of the TV

The TV can be controlled from a PC, control panels and other devices using the RS-232C or IP.

Use a cross-type RS-232C cable, ETHERNET cable (commercially available) or wireless LAN for the connections.

This operation system should be used by a person who is accustomed to using computers.

Communication conditions for IP

Connect to the TV with the following settings made for IP on the PC.

IP protocol:

TCP/IP

Host IP address:

Set the IP address on the TV menu

Service:

None (Do not select Telnet or SSH)

TCP port#:

Set a port number on the TV menu

 

(Control port)

When you set your ID and password on the TV menu, you need to enter them as soon as you connect to the TV.

The connection will be cut off when there has been no communication for 3 minutes.

Communication conditions for RS-232C

Set the RS-232C communication settings on the PC to match the TV's communication conditions.

The TV's communication settings are as follows:

Baud rate:

9,600 bps

Data length:

8 bits

Parity bit:

None

Stop bit:

1 bit

Flow control:

None

Communication procedure

Send the control commands from the PC via the RS- 232C or IP.

The TV operates according to the received command and sends a response message to the PC.

Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the next command.

Command format

Eight ASCII codes e CR

C1 C2 C3 C4 P1 P2 P3 P4

Command 4-digits Parameter 4-digits Return code

IP Control Setup

Example

Initial Menu

Setup

Initial Setup

EZ Setup

Broadcasting Setup

Internet Setup

Language

[English]

DivX® Setup

Command 4-digits: Command. The text of four characters.

Parameter 4-digits: Parameter 0–9, x, blank, ?

Parameter

Input the parameter values, aligning left, and fi ll with blank(s) for the remainder. (Be sure that 4 values are input for the parameter.)

When the input parameter is not within an adjustable range, “ERR” returns. (Refer to “Response code format”.) Any numerical value can replace the “x” on the table.

0

 

 

 

When “?” is input for some

 

 

 

 

commands, the

 

 

 

 

 

 

 

 

 

 

 

 

0

0

0

9

present setting

?

 

 

 

 

 

 

 

value responds.

 

 

 

 

 

 

 

 

 

 

 

 

a

3

0

 

 

?

?

?

?

 

 

 

 

 

 

 

 

 

1Press MENU to display the MENU screen, and then press c/d to select "Initial Setup".

2Press a/b to select "Internet Setup", and then press ENTER.

3Press a/b to select "Network Setup", and then press ENTER.

4Press a/b to select "IP Control Setup", and then press ENTER.

5Press c/d to select "Change", and then press

ENTER.

Response code format

Normal response

Problem response (communication

 

 

 

 

error or incorrect command)

O K

 

 

 

 

 

 

 

 

 

 

 

E R R

 

 

 

Return code (0DH)

Return code (0DH)

 

 

 

 

 

 

 

 

6To use IP Control, press c/d to select "Enable", and then press ENTER.

7Set the device name.

8Set your login ID and password.

9 Set the port to use with IP Control.

10 Confi rm the settings, and then press "OK".

58

Image 60
Contents LC-80LE632U Page LC-80LE632U Model No Serial NoFCC Compliance Statement Industry Canada StatementAdditional Safety Information Dear Sharp CustomerPrecautions when transporting the TV Caring for the cabinetChild Safety Caring for the front panelContents Supplied Accessories Remote control unit AAA size battery70 7/ 8 inches Stand Unit Assembly Attaching the StandBuilding the Work Table Attaching the Stand to the TVInsert the batteries into the remote control unit. See Quick ReferenceInstalling Batteries in the Remote Control Unit Connecting Antenna CablePreparation RS-232C terminal Audio OUT terminalAudio in terminal Remote Control Unit Part NamesConnecting to video equipment or PC Connecting to audio equipmentIntroduction to Connections Types of ConnectionDVI-HDMI conversion cable Mm stereo minijack cable Video Yellow AUDIO-L White AV cable AUDIO-R Red See page 32 for details on the Output Select function Connecting to External Equipment Turning On/Off the Power Initial InstallationLanguage Language setting Watching TVAir/Cable Antenna setting Watching TV Antenna & Cable/STBCH Search Channel search To watch TV via a set-top boxExamples of the settings confirmation screen Watching TV CompletedChanging Volume Sleep TimerDirect Button Operation Changing ChannelsPress Power Saving Direct Button OperationPress Input Press a/b or press Input again to select the input sourceClosed Captions and Digital Closed Captions Press CCExamples This will present the Closed Caption information displayPress View Mode You can select the screen sizeFor HD programs For 43 programsOn-Screen Display Menu On-Screen Display Menu OperationMenu Operation Buttons Lcfont embeddedMenu Items On-Screen Display MenuPicture Settings AV Mode Changing Pic.QualityOPC Setting Advanced Picture SettingsColor Temp Color Temperature Gamma AdjustmentFilm Mode 32 pull-down Motion EnhancementAudio Settings SurroundBass Enhancer Clear VoicePower Control Power SavingNo Signal Off No Operation OffSystem Options View OptionInput Terminal Setting Menu DesignIcon Light Up Setting Demo ModeCaption Setup Game Play TimeInitial Setup EZ SetupBroadcasting Setup CH SetupReset Wall Mount Audio SetupIndividual Setup LanguageWhen setting an individual content-based rating item ChipChip is an electronic fi ltering device built into your TV Parental GuidelinesHow to temporarily release the V-CHIP Block Canadian English RatingsCanadian French Ratings Reactivating the temporarily released V-CHIP BlockSoftware Update InformationIdentification Digital Caption Info Digital Caption InformationOn-Screen Display Menu Press Enter to start checking the data in the USB Memory device Select Yes, and then press EnterDuring the data checking, Checking blinks After the screen shown below is displayed, pressConnecting a Home Network Dlna Server When displaying the data with the Apps Select the Files to Play BackEnjoying Photo/Music/Video Playback USB memory devicePhoto Mode Playing Back Files on a USB Memory DeviceUSB Menu Select Slide Show IntervalSelect Slide Show BGM Buttons for slide show BGM select operationVideo Mode Music ModeUsing the operation panel Menu for playing modeUSB Menu Menu for file selecting operations Title Edition/ChapterDivX Setup Press a/b to select DivX Setup, and then press EnterUSB Device Compatibility DivX VOD registration DivX VOD deregistrationPlaying Back Files on a Home Network Dlna Server Home Network Dlna MenuButtons Description C/d Yellow Display the Home Network Dlna Menu ScreenHome Network Dlna Server Compatibility Presetting Remote Control Function Presetting manufacturer codesOther Viewing Options Operating the Connected EquipmentOther Viewing Options Manufacturer codes Using Aquos Link Controlling Hdmi Equipment Using Aquos LinkUsing Aquos Link Aquos Link SetupOne Touch Playback Link Operation Menu One Touch RecordingStart/Stop Recording Displaying the Link Operation MenuUsing the Device Operation Panel Playback of Titles Using Aquos LinkTimer Recording Manually Changing Aquos Audio Speaker System’s Sound ModeUsing a PC Displaying a PC Image on the ScreenStretch Dot by Dot Adjusting the PC Image Setting Audio InputPC Compatibility Chart Using a PCControl of the TV Using a PC Command table Commands not indicated here are not guaranteed to operateBroadband router ModemInternet Using the Internet +Using the wireless LANInternet Setup Interactive ServiceWireless Setup Checking Your Internet ConnectionDisplaying Updated Information and Support Service Original HomeAquos Advantage Live Entering Text Software Keyboard Using the Browser About linksUsing the Toolbar Using Tabs Selected itemSelected item Description Select This Close This TabSaving the URL of the Current Opening a BookmarkedEditing Bookmarks Browser Settings Security SettingsView Settings Using Applications via the Internet Deactivating Netflix FunctionDeactivating the Vudu Function Disclaimers This message is available only in EnglishAppendix Removing the StandBefore detaching or attaching the stand, unplug the AC cord Before attaching/detaching the standSetting the TV on the Wall Standard dimensions for wall mount BelowWall Mount Kit Specifications AppendixTroubleshooting Pages 24Pages 27 Troubleshooting Error Message Error code Possible Solution Displayed on a screenE202 E203Trademarks Secret number isSpecifications Model LC-80LE632UWireless LAN SpecificationsSpecification Information on the Software License for This Product Software compositionSoftware developed by Sharp and open source software Obtaining source codeInformation on the Software License for This Product Software CopyrightsCalling for Service Limited WarrantyPage Page Dimensional Drawings Unit inch mm Unité pouce mm Unidad pulgada mmSharp Electronics Corporation