Sony SLV-SF900G manual Specifications, System, Inputs and outputs, General, Supplied accessories

Page 100

Specifications

System

Channel coverage

PAL (I)

UHF B21 to B69 RF output signal

UHF channels 21 to 69 Aerial out

75-ohm asymmetrical aerial socket Tape speed

SP: PAL 23,39 mm/s (recording/playback) NTSC 33,35 mm/s (playback only)

LP: PAL 11,70 mm/s (recording/playback)

NTSC 16,67mm/s (playback only) EP: NTSC 11,12 mm/s (playback only)

Maximum recording/playback time

10 hrs. in LP mode (with E300 tape) Fast-forward and rewind time

Approx. 1 min. (with E180 tape)

Inputs and outputs

iLINE-1 (TV) 21-pin

Video input: pin 20

Audio input: pins 2 and 6

Video output: pin 19

Audio output: pins 1 and 3

tLINE-3 IN 21-pin

Video input: pin 20

Audio input: pins 2 and 6 LINE-2 IN

VIDEO IN, phono jack (1)

Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative

AUDIO IN, phono jack (2) Input level: 327 mVrms

Input impedance : more than 47 kilohms AUDIO OUT, phono jack (2)

Rated output level: 327 mVrms

Load impedance: 47 kilohms

Output impedance: less than 10 kilohms

General

Power requirements

220 – 240 V AC, 50 Hz Power consumption

25 W (Normal)

2, 7 W (POWER SAVE is set to ON, no decoder) Operating temperature

5° C to 40° C Storage temperature

–20°C to 60° C Dimensions

Approx. 430 × 100 × 330 mm (w/h/d) including projecting parts and controls

Mass

Approx. 4.8 kg

Supplied accessories

Remote commander (1)

R6 (size AA) batteries (2)

Aerial cable (1)

SmartFile labels (10)

Design and specifications are subject to change without notice.

100

Image 100

Contents Video Cassette Recorder Precautions SafetyInstalling Compatible colour systemsTable of contents Unpacking Setting up the remote commander Using the remote commanderInserting the batteries Remote sensorTV control buttons Fastext buttonsTV/VIDEO Prog +Controlling other TVs with the remote commander TipCode numbers of controllable TVs Manufacturer Code numberConnecting the VCR Connection to your TV with a Scart EURO-AV connectorLINE-1 TV LIGNE-1 TV If the connected TV complies with SMARTLINK, NexTView Link About the Smartlink featuresCinemaLink*2, Q-Link*3or T-V To mains Aerial cable supplied Signal flow Connection to your TV with an aerial cable onlyConnection to your TV and Set-Top Box STB If your STB has a Scart EURO-AV connectorIf you don’t use a STB, skip to Additional connections If your STB does not have a Scart EURO-AV connectorTo a stereo system Turn on your TV and press ?/1 on/standby to turn on the VCR Tuning your TV to the VCRPull down the drop down panel Selected for ex. programme position To check if the TV tuning is correctTo obtain a clear picture from the VCR Window. The RF channel is then switched off Press RF Channel againSetting up the VCR with the Auto Set Up function Hold down Auto SET UP on the VCR for more than 3 secondsTo cancel the Auto Set Up function Press Auto SET UPSetting the clock manually Setting the clockBefore you start… ADJUST, then press OK Press , to highlight the month and setMonth pressing M/m ClockTip Changing the station for the Auto Clock Set function Auto Adjust is highlightedPress OK Press M/m to highlight ON, then press Press m to highlight ClockPROGRAM, then press OK TipsSelecting a language Press M/m to highlight LANGUAGE, then press OKPress M/m to highlight TUNER, then press OK Presetting channelsPress M/m to highlight Channel Position If the picture is not clear Disabling unwanted programme positionsPosition Highlight Lists and press OK Setting/changing the station namesPress M/m to highlight Channel LIST, then press OK To correct a character, press is highlighted, then reset it Changing/disabling programme positions Changing programme positionsPosition, then press To display other pages for programmePositions 6 to 60, press M/ m repeatedly Selected channel is inserted atHighlight LISTS, and press OK Press M/m to highlight the row which you want to disable Setting your personal code Hold down first X pause, hold on ?/1On/standby simultaneously on the VCR For more than 3 secondsConfirmation screen appears Press M/m//, to enter your personal codePress ?/ 1 on/standby to turn off the VCR Checking your personal code Press OK to exit the menuPlaying a tape When your TV is Set Ntsc PB to Additional tasksTo play an NTSC-recorded tape To use the time counterTip Recording TV programmes Turn on your TV and set it to the video channelTo record from a decoder or other source, turn it on Prog + REC StopTo stop recording To check the remaining time To watch another TV programme while recordingTo protect a recording Time counterRecording what you are watching on the TV TV Direct Rec Number Recording TV programmes using the Video Plus + systemButtons Press Timer When you set Timer Options to Video Plus +Video Plus +, menu appears on TV screenPress To highlight the item you Press M/m to reset itWant to change To use the VCR after setting the timer Press ?/1 to turn off the VCRTo stop the VCR while recording, press x Stop Daily/weekly recordingVariable Setting the timer manually Or LINE-3 in connectors, or the LINE-2 INjacks, press Input Timer menu appears on the TV screenSelect to display L1, L2, or L3 in the PROG. position To stop recording Playing/searching at various speeds Slow REW Playback options OperationPress H playback To resume normal playbackPlayback options Operation Setting the recording duration time To cancel the durationAutomatically after a specified duration To extend the durationHow to connect for Synchronized Recording Synchronized RecordingPress Synchro REC. The Synchro REC indicator turns off To cancel the Synchronized Recording functionPress x Stop while recording Checking/changing/cancelling timer settings When the timer settings overlap ProgrammeNicam system Recording stereo and bilingual programmesSelecting the sound during playback How sound is recorded on a video tape Stereo Bilingual Usually mixed Left/right channelsNormal audio track monaural Stereo soundSearching using the index function To stop searchingAdjusting the picture Adjusting the trackingAbout the Reality Regenerator RR function About the Optimum Picture Control OPC functionOPC recording To deactivate the OPC functionInitial settings are indicated in bold print Changing menu optionsPressOK. MENU, then select Options and press Video Options menuAudio Options menu Tape Options menuOther Options menu Other OptionsHow to connect to record on your VCR Connecting to a VCR or stereo systemVMC-820 audio/video cable not supplied How to connect to a stereo system When recording on your VCR Basic EditingBefore you start editing To stop editingRecording using the SmartFile function Checking the contents of a tapeAbout the SmartFile function Selecting and playing a programmeLabelling a recorded programme and tape Protecting a recorded programmeErasing the data of an unwanted programme Running a demonstrationRecording using the SmartFile function Attaching the SmartFile label to the cassetteRecording a programme on the SmartFile tape Checking the information of a recorded programme Date Day of the weekRecording start time Recording time Tape speed Station nameRecording after locating the Blank Time space Press M repeatedly to select Blank TimeStart END Select Search OK Exit Menu NOW Searching Selecting and playing a programme Checking the contents of a tape SmartFile function Labelling a recorded programme and tape Setting the TV guide page numberTape title Category Automatically when the VCR detects them TV guide page numbers appearP301 If the VCR does not detect them P---, you Have to set the appropriate TV guideLabelling a recorded programme and tape Labelling a recorded programme manually Smartfile EditClear To erase the programme label To label a regularly scheduled timer-recorded programmeTo erase the selected category Labelling a tape To erase the tape title To stop registration to the SmartFile label Press Smartfile GeneratorRegistration date Programme located in a recorded tape To check the information of a registered programmeRecording time Tips Protecting a recorded programme Press Smartfile SmartFile search list disappears To unlock the protected programmeErasing the data of an unwanted programme SP 1H 30M Nick & Matt Troubleshooting Problem summaryInitial Terminal Contamination Playback S10 Normal recording S11S12 SmartFile S13 Timer recording S15 Remote Commander S20 S16 Synchronized Recording S17Cleaning S22 Power S24Power S25 S21Set-Top Box control S32 Specifications Supplied accessoriesSystem Inputs and outputsFront panel Index to parts and controlsRefer to the pages indicated in parentheses for details Display window Antenne Sortie connector 9 Ntsc PB Play Back switch Antenne Entree connector 9Rear panel Remote commander 104TV/VIDEO remote control switch ?/1 on/standby button 6 Menu chart 106107 108 109 Connecting Index