Sony SLV-685HF manual Symptom Remedy, Others

Page 64

Troubleshooting (continued)

64

 

Symptom

Remedy

 

A TV program does not appear

• Make sure the TV is set to the channel for the VCR. If

 

on the TV screen.

you are using a monitor, set it to video input.

 

 

 

 

 

 

 

 

TV reception is poor.

• Adjust the TV antenna.

 

 

 

 

 

 

 

Recording

The tape starts playing as soon

• The safety tab has been removed. To record on this

as it is inserted.

tape, cover the tab hole.

 

 

 

 

 

 

 

 

 

The tape ejects when you press

• Check that the safety tab has not been removed.

 

rREC.

 

 

 

 

 

 

 

 

 

 

 

 

 

Nothing happens when you

• Make sure the tape is not at its end.

 

press r REC.

• Select the correct source. Select a channel number with

 

 

the CH +/– buttons when recording TV programs;

 

 

select “L1” or “L2” with the INPUT SELECT button

 

 

when recording from other equipment.

 

 

 

 

 

 

 

 

The timer does not operate.

• Check that the clock is set.

 

 

• Make sure a tape has been inserted.

recording

 

• Check that the safety tab has not been removed.

 

• Make sure your timer settings have not already passed

 

 

• Make sure the tape is not at its end.

 

 

• Make sure a program has been set for timer recording.

Timer

 

the current time.

 

• Check that the cable box is turned on.

 

 

 

 

• The clock stops if the VCR is disconnected from the

 

 

wall outlet for more than one hour. Reset the clock and

 

 

timer.

 

 

 

 

 

 

 

 

A tape cannot be inserted.

• Check that a tape isn’t already in the tape

 

 

compartment.

 

 

 

 

 

 

 

 

The remote commander does

• Make sure you are pointing the remote commander at

 

not function.

the remote sensor on the VCR.

 

 

• Replace all the batteries in the remote commander with

 

 

new ones if they are weak.

 

 

• Make sure the

TV

/

VTR

remote control switch is set

Others

 

correctly.

 

 

 

 

 

 

 

 

 

 

The tracking indicator does not

• The recording condition of the tape is very poor and

appear on the screen.

tracking cannot be adjusted.

 

 

 

 

 

 

 

 

You cannot control other TVs.

• Set your TV’s code number. The code number resets to

 

 

01 when you replace the batteries of the remote

 

 

commander.

 

 

 

 

 

 

 

 

The VCR needs to be cleaned.

• Clean the cabinet, panel and controls with a dry, soft

 

 

cloth, or a soft cloth slightly moistened with a mild

 

 

detergent solution. Do not use any type of solvent,

 

 

such as alcohol or benzine.

 

 

 

 

 

 

 

Additional Information

SONY SLV-685HF (E) 3-859-040-11 (1)

Image 64
Contents Video Cassette Recorder Owner’s recordPrecautions SafetyInstalling InformationTable of contents Unpacking Getting StartedSetting up the remote commander Using the remote commanderInserting the batteries You can use this remoteCode numbers of controllable TVs Controlling other TVs with the remote commanderManufacturer Code Number Selecting the best hookup option HookupsBefore you get started Use this hookup if your TV has stereo jacks Use this hookup if your TV doesn’t have stereo jacksStrereo receiver Audio/video cable suppliedGetting Started Using cable box control Recommended useWhat you can do with this hookup What you can’t doCH 3 or CH 4, whichever Set the RF Unit switch toCursor Channels Hookup 1 VCR Plus+ channel setupProgram guide channel Your actual TV channel For connector Record scrambled channels that require a cable boxYou dont have a Cable box UHF connectionHookup 2 VCR setup Normal displayHookup 2 VCR Plus+ channel setup Use this hookup if you’re using Antenna hookupTV A, B, or C Match the typeHookup 3 VCR setup Hookup 3 VCR Plus+ channel setup Incompatible cable box with many scrambled channels Wall Cable boxHookup 4 VCR setup Hookup 4 VCR Plus+ channel setup Program guide channel Cable box output channelDSS Digital Satellite System receiver ∙ Record programs with VCR Plus+No UHF DSS receiver Side viewHookup 5 VCR setup Wall Splitter Switch Cable box For connector types B and C, no UHF connection is requiredHookup 6 VCR setup Tuner Preset CH3 Hookup 6 VCR Plus+ channel setup Selecting a language You can change the on-screen display languagePress Cursor /.to select ENGLISH, ESPAÑOL, or Français Then press ExecuteSetting the clock Before you start…Setting up cable box control Skip this section if you are using Hookup 2, 3, 4 orPress Cursor ?//to select ON, then Press CursorNumber from the chart below Press the number buttons to enterCable box/DSS receiver code number, then Find your cable box/DSS receiver codeSetting up cable box control DSS receiver Code numbers BrandSignal flow To check the cable box control settingTo ensure correct operation Setting up cable box control Presetting channels Presetting all receivable channels automaticallyTurn on the VCR and the TV Press Cursor /.to select ANTENNA/CABLEPresetting channels Presetting/disabling channels manually Channel to be presetChannel to be disabled CH +If the picture is not clear Setting up VCR Plus+ How to set up your VCRExample of Channel Line-up Chart How VCR Plus+ worksSetting up VCR Plus+ Repeat steps 2 and 3 for each channel When you’ve finished, press Menu to exitWhose numbers don’t match Playing a tape Turn on your TV and set it to the video channelBasic Operations StopAdditional tasks To skip playbackTo use the time counter Basic OperationsInsert a tape with its safety tab in place Recording TV programsTo record from a cable box, turn it on RECBasic To stop recordingTo check the remaining time OperationsTo watch another TV program while recording Safety tab TipsTo save a recording Press VCR Plus+ Recording TV programs using VCR Plus+Number buttons Using Cursor ?//, then press SET Timer Clear to cancel the settingTo enter another setting, repeat steps 1 to Press Tape Speed to select SP or EPTo lock the VCR after setting the timer Child Lock To use the VCR after setting the timerTip Setting the timer manually Press Menu and select Timer SET/ CHECK, then press ExecuteSetting, move the cursor to the next line and repeat step Set the date, start and stop times, channelNumber and tape speed Press ExecuteTo resume normal playback Playing/searching At various speedsPress áPLAY Recording TV programs using the quick timer Using the quick timer during stop modePress Quick Timer repeatedly to set to the new duration To extend the durationChecking Changing Canceling timer SettingsWhen the timer settings overlap Turn on your TV and set it toRecording stereo and bilingual programs Recording stereo programsRecording bilingual programs Selecting the sound while playingHow sound is recorded on a video tape Adjusting the picture Adjusting the trackingAbout Adaptive Picture Control APC APC playbackInitial settings are indicated in bold print Changing menu optionsPress Menu and select Advanced Options Menu choicesHow to hook up to record on this VCR How to hook up to a stereo systemVMC-810 audio/video cable not supplied Signal flow Editing with another VCROperation When recording on this VCR Before you start editingTo stop editing Press the p Stop buttons on both VCRsSetting the RF unit General setup informationAdditional Information Ohm twin lead cable EAC-32 Antenna connector not supplied Attaching the external antenna connectorAttaching a UHF/VHF band mixer Troubleshooting Symptoms caused by contaminated video headsSymptom Remedy OthersSpecifications Front panel Index to parts and controlsRefer to the pages indicated in parentheses for details Display window Rear panelRemote commander J, K IndexX, Y, Z Quick reference to using the VCR To play a tapeTo record a program To watch TVSony SLV-685HF E 3-859-040-11