Panasonic DMR-EX79 Changing the unit’s settings, Settings for Analogue Channels, Signal Condition

Changing the unit’s settings

Signal Condition

You can check the quality and strength of digital broadcast signals. Realign the aerial if you are receiving a poor signal.

When “Signal Condition” is displayed in grey and cannot be selected:

1Press [EXIT] to exit the screen.

2Press [W X CH] to select a digital channel. “D” appears on the unit’s display.

3Display the Setup menu again (> 59).

Press [3, 4] to select “Signal
	DVB Signal Condition
Condition” and press [OK].	DVB Channel		[CH14] 5 BR3
The quality and strength of the
	Signal Quality	0		10
signal are shown.	Signal Strength	0		10
Press [W X CH] to select the			Channel +
	RETURN		Channel –

channel.

Signal Quality Below 2 (display red):

The signal quality is so poor that there may be interference in the pictures and sound.

2–5 (display orange):

The signal quality is basically adequate, but brief interference in the pictures and sound is possible in isolated case.

Over 5 (display green):

Optimum picture and sound quality.

Signal Strength

The display for signal strength is grey. “0” means signal strength 0%, “10” means signal strength 100%.

If the signal is too strong, the display will change from grey to red. Reduce the signal amplification at your aerial.

≥When the signal is weak:

–adjust the position and direction of the aerial.

–adjust the aerial reception with “DVB Manual Tuning” in the Setup menu (> 59).

–check that the current digital broadcast channel is correctly broadcasting.

∫Settings for Analogue Channels

Press [OK] to show the following setting.

Manual Tuning

You can delete analogue channels and set the analogue channel details.

Press [OK] to show Manual Tuning screen.

		Manual Tuning
		Pos	Channel	CH	Pos Channel	CH
		1	ARD	4	11
		2	ZDF	2	12
		3	N3	5	13
		4	HR3	8	14
		5	BR3	10	15
		6			16
SELECT		7			17
OK		8			18
	RETURN	9			19
Delete		10			20

To delete a programme position

Press [3, 4, 2, 1] to select a programme position and press the “Red” button.

To change the tuning settings for individual programme position

1Press [3, 4, 2, 1] to select a programme position and press [OK].

Manual	Pos	901
Tuning	Channel	ARD
	CH	4
	Fine Tuning	Auto
	Mono	Off

SELECT

RETURN

RETURN : leave

2Press [3, 4] to select an item and press [1].

Pos	Programme position in the table
	(You cannot change the programme position.)
Channel	To enter or change the Channel of a TV
	station
	Press [3, 4, 2, 1] to enter station name
	and press [OK].
	If the station name needs a blank space,
	select the blank between “Z” and “¢”.
CH	To enter newly available TV stations or
	change the CH number of an already tuned
	TV station
	Press [3, 4] or the numbered buttons to
	enter the CH number of the desired TV
	station.
	Wait a few moments until the desired TV
	station has been tuned.
	After the desired TV station is tuned, press
	[OK].
Fine Tuning	To obtain the best tuning condition
	Press [3, 4] to adjust the best tuning
	condition and press [OK].
	≥Press [1] to return to “Auto”.
Mono	To select the type of sound to be recorded
	Press [3, 4] to select “On” if the stereo
	sound is distorted due to inferior reception
	conditions, or if you want to record the normal
	(mono) sound during a stereo or bilingual
	broadcast, and press [OK].

RQT9306

60