Sylvania LC195SLX 5Initial Setup, Before you begin, After an initial setup is completed

Español Français English

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

5Initial Setup

INTRODUCTION

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and autoscan, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure the unit is connected to antenna or cable.

1After making all the necessary connections, press [POWER] to turn on the unit.

• This operation may take a few moments.

2Use [Cursor K/L] to select the on-screen language from the choices on the right side of the TV screen. (English / Español / Français)

InitialI i i l Setup

Select the language for setup display.			English
Elija el idioma de ajuste.			Español
			Français
Sélectionner langue écran config.
Select	ENTER Enter	SETUP
			Skip

•“Initial Setup” menu on step 3 will be displayed in the selected language after you press [ENTER].

3Use [Cursor K/L] to select “Antenna” for TV channels or “Cable” for CATV channels, then press [ENTER].

InitialI i i l Setup

Make sure the antenna is connected to“ANT. IN” jack.			Antenna
Select the destination of “ANT. IN” jack.
			Cable
			Skip
Antenna	Or
Cable			ANT.IN
Select	ENTER Enter	BACK	SETUP
		Back	Skip

• “Autoscan” will begin.

InitialI i i l Setup

Now the system is scanning for channels,please wait.

Autoscan will take up to 20 minutes to complete.

0%

Analog channels	0ch
Digital channels	0ch

SETUP

Skip

4 Use [Cursor s/ B] to select the desired location setting,								PREPARATION
	then press [ENTER].
			InitialI i i l Setup
			Select “Retail” or “Home” for your location.
				Retail
							Home
								WATCHING
				Select			ENTER Enter
	• Select ”Retail”, the unit will be set up with predefined
	setting for retail displays. In this setting, the power
	consumption may possibly exceed the limited							TV
	requirement of the ENERGY STAR® qualification.
	• Select ”Home”, the unit is set to maximize the energy
	efficiency for home setting and it can be adjusted							OPTIONAL
	through a choice of picture and sound quality
	according to your preference.
	• When the initial setup is completed, the lowest							SETTING
	memorized channel with the confirmation message
	of the location setting will be displayed on the TV
	screen.
								TROUBLESHOOTING
	Note:
	• If you connect the cable system directly, contact the CATV
	installer.
	• If you press [POWER] or [SETUP] during autoscan, this
	setting will be canceled.
	• The initial autoscan function can be executed for either
	“Antenna” or “Cable” only once. When you change the
	connection (Antenna / Cable), set autoscan again.
	(Refer to page 18.)							INFORMATION
	• If there is no signal input from the antenna terminal and
	no operation for several seconds after you turn on the unit,
	“Helpful Hints” appears. Follow the instructions listed on
	the TV screen.
		InitialI i i l Setup
		No channel is registered.				Retry
		Try Autoscan again?				Later
		Verify that you have a cable connected to the " ANT. IN" jack
		on the back of the TV, the channel installation process
		searches this connection. If you are using a cable or satellite
		box, please confirm the input which you have connected the
		box and press the “INPUT SELECT” key on the remote control to
		select the appropriate source input.
		Select	ENTER Enter	SETUP
					Skip

•You must set ”Home” in step 4. Otherwise, the settings of picture and sound quality you adjusted will not be memorized after you turn off the unit.

After an initial setup is completed...

•If you want to scan the channels automatically again, refer to “Autoscan” on page 18.

•You can add the desired channels unmemorized by “Autoscan”. Refer to “Manual Register” on page 19.

•If you want to change to another language, refer to “Language Selection” on page 20.

•If you want to change the location setting, refer to “Location” on page 31.

13

EN