Sylvania LD190SS1 owner manual  Troubleshooting Guide

Page 50

TROUBLESHOOTING

Troubleshooting Guide

If the unit does not perform properly when operated as instructed in this manual, check the following chart and all connections once before calling for service.

Symptom

Remedy

		• Make sure the AC power cord is plugged in.
	No power	• Make sure that the AC outlet supplies the proper voltage, plug another electrical
	No power	appliance into the AC outlet.
		• If a power failure occurs, unplug the AC power cord for 1 minute to allow the unit
		to reset itself.
	Control button does not work.	• Press only one button at a time. Do NOT press more than one buttons at the same
	Control button does not work.	time.
		time.
		• Check whether the connection of the antenna, cable receiver or satellite box is
		connected correctly.
	Power is ON but no screen	• Check whether all the cables to the unit are connected to the correct output jack
	Power is ON but no screen	of your device like BD/DVD recorder.
	image.	of your device like BD/DVD recorder.
	image.	• Make sure that the selected input mode is connected to the working input jack.

		• Check if your computer is NOT in sleep mode when the input mode of this unit is
		in PC mode. Tap any key on the keyboard to wake up your computer.
		• Check if the power is on.
		• Check if the right input mode is selected.
		• Check whether all the cables to the unit are connected to the correct output jack
		of your device like BD/DVD recorder.
		• View other TV channels. The problem might be limited to the broadcasting station.
		• Turn off the unit and wait for about 1 minute, then turn on the unit again.
	No picture or sound	• Check whether the connection of the antenna, cable receiver or satellite box is
	No picture or sound	connected correctly.
		• Make sure that the selected input mode is connected to the working input jack.
		• Check if your computer is NOT in sleep mode when the input mode of this unit is
		in PC mode. Tap any key on the keyboard to wake up your computer.
T		• Make sure that the sound is not muted. Press [ MUTE] so that the volume bar
T		and current volume level will appear on the TV screen.
		and current volume level will appear on the TV screen.
V		• Make sure that the volume is NOT set to “0” or “Mute”. If so, use [VOL. X / Y] to
V		adjust the desired volume.
	No color	• View other TV channels. The problem might be limited to the broadcasting station.
	No color	• Adjust “Color” in the main menu.
		• Adjust “Color” in the main menu.
	Adjusted ‘‘PICTURE” or ‘‘SOUND”	• You must set ”Home” in ”Location”. Refer to page 33.
	is not effective every time turn	Otherwise, the settings you adjusted will not be memorized after you turn off the
	on the unit.	unit.

		• Electrical interference from nearby appliances may affect picture quality.
		• Adjust “Contrast” and “Brightness” in the main menu.
	Sound OK, picture poor	• View other TV channels. The problem might be limited to the broadcasting station.
		• For the best picture quality, watch “high definition” wide screen programs.
		If the HD content is not available, watch “standard definition” programs instead.
	Picture OK, sound poor	• View other TV channels. The problem might be limited to the broadcasting station.
	Picture OK, sound poor	• Check if the audio cable is connected in correctly.
		• Check if the audio cable is connected in correctly.
	You see a distorted picture or	• You may be getting interference from electrical appliances, automobiles,
	You see a distorted picture or	motorcycles or fluorescent lights.
	hear an unusual sound.	motorcycles or fluorescent lights.
	hear an unusual sound.	• Try moving the unit to another location to see if this is the cause of the problem.

	Ghosts, lines or streaks in	• Electrical interference from nearby appliances may affect picture quality.
	picture	• View other TV channels. The problem might be limited to the broadcasting station.

	You see “noise” or “trash” on the	• When the capabilities of the unit exceed the capabilities of the digital
	screen.	broadcasting, the signal will be increased to match the capabilities of the display
	screen.	of the unit. This may cause noise or trash.
		of the unit. This may cause noise or trash.
	Different color marks on the TV	• View other TV channels. The problem might be limited to the broadcasting station.
	screen

50

EN

Image 50

Contents LD190SS1  Precautions FCC Warning Trademark Information Introduction  Supplied Accessories Symbols Used in this Manual  Attaching the Stand Features DTV/TV/CATV Contents TV Functions DVD Functions Control Panel Terminals Remote Control Function  Installing the Batteries Battery Precautions Connection to Cable Receiver or Satellite Box Preparation Antenna Connection Satellite providerHDMI-DVI Connection  External Device ConnectionHdmi Connection Component video Connection Video ConnectionInformation PC Connection  Plug In the AC Power CordResolution Before you begin TV Functions  Initial SetupAfter an initial setup is completed Make sure the unit is connected to antenna or cableWatching TV  Volume Adjustment Sleep Timer  Channel SelectionSwitching Audio Mode  Still Mode Switching Each Input Mode Press Info  TV Screen InformationBroadcasting information Program title Program guide TV Screen Display Mode  Autoscan Optional Setting Main Menu Using CH K/L Channel List Manual RegisterUse Cursor K/ L to select Antenna, then press  Antenna Confirmation Language Selection AntennaAdjust the picture quality  Picture AdjustmentPicture Mode Adjust the following items  Sound AdjustmentSound Mode TV Speakers Closed Caption Caption ServiceCaption mode Service 1~6 Digital Caption ServiceUse Cursor K/L to select User Setting, then press Closedl CaptioniEdge Type Font StyleFont Size Font ColorUse Cursor K/L to select Child Lock, then press Enter password Child Lock Childild LockChannel Lock Mpaa RatingUse Cursor K/L to select TV Rating, then press TV RatingTo set the sub ratings TV RatingiNew Password Enter password Confirm password New PasswordUse Cursor K/L to select New Password, then press Enter Clock, Phase  PC SettingsAuto Adjustment Horizontal Position, Vertical PositionLocation  Energy Saving ModeEnergy Savingi Mode Use Cursor K/L to select the desired mode, then press EnterCurrent Software InfoI  Current Software InfoConfirm the version of the software currently used  Unplayable Media Operating DVDDVD Functions Playable Media  Resume Playback  Playback Disc Menu DVD Zoom  Fast Forward / Fast Reverse Slow Forward / Slow Reverse Chapter / Title / Track Search During playback, press Mode repeatedly until / appears Search Functions You can select chapters, titles or tracks on the discRepeat Playback Time SearchDirect Search You can repeat playback between a and B on a disc Repeat A-B Playback Programmed Playback Random Playback Playback Special Settings On-screen Display Use Cursor K/ L repeatedly until your desiredCamera Angles Black Level SettingPress Cursor K/ L to adjust the black level Audio LanguagePress Cursor K/ L to select the sound level Stereo Sound ModeVirtual Surround Press Setup to display the main menu DVD Setting DVD Language Setting Subtitle *1, *2Default OFF DVD Audio Setting Down SamplingNumber buttons to enter the current 4-digit password  Parental SettingIf you have set password already, use Use the Number buttons to enter the new 4-digit password Others You can change the other functionsUse Cursor K/ L to select YES, then press Enter  Reset to the Default Setting  Language Code ListUse Cursor s / B to select , then press Enter Troubleshooting Troubleshooting  Troubleshooting GuideTape containing captions Have been read during copying During playback Angle does not switchCaptions are displayed as a Make sure the disc is compatible with the unit Glossary  MaintenanceInformation NtscOther Specifications  General Specifications Electrical Specification CatvLimited Warranty Ninety 90 DAY Labor / ONE 1 Year Parts Español Français English