CODEProgramming, Press the OK button T | Panasonic NV-FJ730 specification

DATE CH ON OFF

27SA 2 1 3 : 4 5 1 4 : 1 5 SP

CATEGORY : 1

SP OFF

DATE CH ON OFF

27SA – – 1 3 : 4 5 1 4 : 1 5 SP

CATEGORY : 1

G-CODE

---------

END:G-CODE

G-CODE

123456---

On Screen Display

G-CODEProgramming

Programming is now easier than ever; simply enter the G-CODEnumber found in the programme scheduling pages of newspapers and magazines.

G-CODEnumbers are numbers assigned to programmes listed in the TV programme schedule found in newspapers and TV guides. When these numbers are entered, the numbers are converted to actual programming.

G-CODEis a registered trademark of Gemstar Development Corporation. The G-CODEsystem is manufactured under license from Gemstar Development Corporation.

Preparations

–Confirm that the VCR is on.

–Confirm that the TV is on and the VCR viewing channel is selected.

–Insert a video cassette with an intact erasure prevention tab.

–Set the VCR/TV switch E to [VCR].

–Check that the clock is set to the correct time. If it has not been set, refer to page 10.

Example:

Programming a timer recording of a TV programme with the G-CODEnumber 123456

Operations

1 Press the G-CODE button K to display the menu for entering the G-CODEnumber on the TV.

2 Press the Numeric buttons 2 to enter the G-CODEnumber.

–It is also possible to check the

number with VCR display without	PROGRAMME SET :OK
number with VCR display without	END:G-CODE
appearing the On Screen Display.

–If you have entered the wrong number, press the CANCEL button ; then enter the proper number. An alternative method is to press the Cursor button (2) S and then enter the proper number.

3Press the OK button T.

–The entered programme appears on the display.

–The starting time and the ending

time appears alternately each

5 seconds on the VCR display.

VCR display

SP ON

–Confirm that the number corresponds to the right

programme. If the display looks like this and Á on the VCR display flashes on and off: select the desired programme position using the CH button :, then press the OK button T.

–To make any corrections, use the DATE button 9, the ON button D, the OFF button C and the SPEED button B the same way as described on page 20.

4Press the Cursor button (1) S to select the Category.

Then, select the desired category by pressing the Cursor buttons (3421) S.

CATEGORY SETTING		CATEGORY SETTING
≥MOVIE	≥SPORT	≥MOVIE	≥SPORT
≥MUSIC	≥CHILD	≥MUSIC	≥CHILD
≥DRAMA	≥NEWS	≥DRAMA	≥NEWS
≥EDUCA	≥OTHER	≥EDUCA	≥OTHER
≥DOCUM	≥– – – – –	≥DOCUM	≥– – – – –
	END : MENU		END : MENU

–Alternatively, you can set the category on the Navigator list. (See page 23 for details.)

–This function is activated when [JET NAVIGATOR] is set to [ON]. (See page 13.) When [JET NAVIGATOR] is set to [OFF], procced to the step 6.

5Press the MENU button U to make the previous display

appear.	DATE CH ON		OFF	1 5 SP
	27SA	2 1 3 : 4 5	1 4 :	1 5 SP
	CHECK	: PROG./CHECK

6Press the TIMER (REC) button A to switch the VCR over to the timer recording standby mode.

–When [JET NAVIGATOR] is set to [ON], the

[PROGRAMME IS COMPLETE. REMAINING PROGRAMME 49.] message appers. (See page 13.)

–When [JET NAVIGATOR] is set to [OFF], the [PROGRAMME IS COMPLETE.] message appears. (See page 13.)

–Check that [Á] is lit on the VCR display.

If it is flashing, check the timer recording details again. (See page 21.)

Notes:

–When the G-CODEnumber is used for programming, the recording time may be slightly longer than the actual programme time.

–Repeat steps 2 and 3 if [PROGRAMME IS INCOMPLETE.] appears.

–When programming two or more programmes, repeat steps 1–6.

–The procedures for checking and cancelling a timer programme are the same as on page 21.

To Suspend the Timer Recording Standby Mode

See page 20.