Panasonic NV-HV60 Setting the Remote Control to Operate Your TV, Basic Connections

Setting the Remote Control to Operate Your TV

You can operate the TVs of the manufacturers listed below with the remote control after setting it.

This setting procedure allows you to operate the TVs of some manufacturers using the supplied remote control.

Preparation

• Set [VCR/TV] switch (22) to [TV].

Operations

1Find the manufacturer number of your TV while referring to the following table.

2While holding down [TV-ON/OFF] (1) on the remote control, use [Numeric] (2) to enter the manufacturer number. This completes the settings for the TV manufacturer.

•Be sure to enter the number in two digits. Example: 1 ) 01

3To confirm the correct settings were made, check whether the TV can be operated properly.

•When a manufacturer has multipled numbers in the following table, try entering other numbers if the TV operations cannot be performed properly, and then select the optimal number.

Notes:

•If you are using a Panasonic TV, this setting has already been made, and so you do not need to perform the above setting procedure. However, this remote control may not work with some Panasonic TVs.

•Some TV models cannot be operated using this remote control (including all TVs non-remote compatible).

List of TVs Compatible with the VCR Remote Control

[Brand]	[Code]
Panasonic/National	01-04
SONY	05
TOSHIBA	06
JVC	07
HITACHI	08
MITSUBISHI	09, 10
SHARP	11
PHILIPS, SAMSUNG	12
NEC	13
SANYO	14
GOLDSTAR/LG	15, 16
SAMSUNG	17,18
SANYO	19

Connections

This section shows you how to connect the VCR to an aerial, TV, etc.

When the VCR is turned on after unpacking and connecting the aerial cable and the mains lead, Plug in Auto Tuning starts automatically. (NV-HV60GN only)

Basic Connections

The following connections are required to record and play back the video cassette through the TV.

		(1)
	(3)	(2)
		(4)
	VIDEO2	2 IN
	AC IN ~
	L 2
(6)	AUDIO
	R 2	2 OUT
	IN (AV1) OUT	RF
		(5)
	¢
(1) Aerial (Not supplied)		(6) AC Input socket (48)
(2) TV Set (Not supplied)		¢ To mains supply

(3)Aerial Connector

(4)RF IN socket (51)

(5)RF OUT socket (52)

Connection to a TV using the Audio/Video Input Socket:

Set the RF output channel of the VCR to [ss] (RF OFF) when the VCR is connected to the TV via the Audio/Video cable. (See page 6.)

				(1)
		(3)	(2)
		(4)	(5)
			(6)	(7)
	AC IN ~	VIDEO2	2 IN
		L 2
	(10)	AUDIO
		R 2	2 OUT
		IN (AV1) OUT	RF
		(9)		(8)
	¢
(1)	Aerial (Not supplied)		(9) VIDEO OUT (50)/
(2)	TV Set (Not supplied)		AUDIO OUT (53)
(3)	Aerial Connector		(10)AC Input socket (48)
(4)	VIDEO IN		¢ To mains supply

(5)AUDIO IN

(6)AV Cable (Supplied)

(7)RF IN socket (51)

(8)RF OUT socket (52)

Connection to a Stereo Amplifier:

		(2)
VIDEO2		¢
AC IN ~
L 2
AUDIO
R 2		(3)	(1)
IN (AV1)	OUT
(5) (4)

(1) Stereo amplifier (Not supplied) ¢ Audio Cables (Not supplied)

(2)REC

(3)PLAYBACK

(4)AUDIO OUT (53)

(5)AUDIO IN (54)

5