Panasonic NV-HV60 specifications Manual Tuning Procedure, Direct Tuning, Fine Tuning Procedure

Page 8

Manual Tuning Procedure

1Press [MENU] (7) to display the Main menu on the TV screen.

2Press [Cursor] (37) (34) to select [TUNER PRESET] then press [OK] (23).

3Press [Cursor] (37) (34) to select [CH] then select the channel number you want to tune by pressing [Cursor]

(37)(21).

4Confirm that [CLEAR] is set to [OFF].

5Press [Cursor] (37) (34) to select [SEARCH] then press [Cursor] (37) (21) to start the Manual Tuning.

• If the desired TV station has not been tuned, press [Cursor] (37) (21) again.

• Press [MENU] (7) and repeat steps 3-5for each programme position you want to tune to a station.

CH 2

SEARCH

CH 2

SEARCH 74

 

END: MENU

 

 

 

END: MENU

 

 

 

 

6Press [MENU] (7) three times to exit the On Screen Display.

Direct Tuning

Follow steps 1 to 3 of Manual Tuning Procedure.

4Confirm that [CLEAR] is set to [OFF].

5Press [Cursor] (37) (34) select [SEARCH].

6Press [Numeric] (2) to enter the number of the desired programme position.

For the 5A and 9A channels, input the following numbers:

90 for CH-5A, 91 for CH-9A. (Example for NV-HV60GL.)

• For other channels that require tuning, repeat steps 3-6.

7Press [MENU] (7) twice to exit the On Screen Display.

Fine Tuning Procedure

Follow steps 1 to 3 of Manual Tuning Procedure.

4Press [Cursor] (37) (34) to select [FINE] then press [Cursor] (37) (21) to obtain the best tuning condition.

• Press [OK] (23) to return the tuning to its former state.

CH 2

 

 

 

AFC: OK

FINE

 

:

 

END: MENU

 

 

 

 

 

 

5 Press [MENU] (7) to exit the On Screen Display.

Blanking of Unused Programme Positions

Follow steps 1 to 3 of Manual Tuning Procedure.

4Press [Cursor] (37) (34) to select [CLEAR] then press [Cursor] (37) (21) to select [ON].

Repeat steps 3-4for other unused programme positions to skip during the selection of programme positions.

To cancel the blanking of a programme position select that programme position then set [CLEAR] to [OFF].

5Press [MENU] (7) twice to exit the On Screen Display.

8

Image 8
Contents Contents Video Cassette RecorderCondensation may form in the following cases For your safetyInserting Remote Control Batteries Controls and Components 5453Picture Mode Timer Check Prog GuideProg Play PROG/CHECKBasic Connections Setting the Remote Control to Operate Your TVConnections Tuning the TV to Your VCR For NV-HV60GL/AustraliaFor NV-HV60GN/New Zealand To Change the RF output ChannelAuto Tuning Using the On Screen Display Plug in Auto Tuning NV-HV60GN/New ZealandStoring TV Broadcasts in Your VCR Pre-programmed TV Channels NV-HV60GL/AustraliaManual Tuning Procedure Direct TuningFine Tuning Procedure Blanking of Unused Programme PositionsSetting the Clock of Your VCR Time Reset FunctionTo Set the Colour TV System Settings Using the On Screen DisplayTo Make Various Indicators Appear On Screen Display Option Setting Playback To Play back S-VHS Cassette Tape SQPB=S-VHS Quasi PlaybackTo Play Back a Recorded Part Repeatedly Ntsc PlaybackRecording To reset the tape counter To Display the Approximate Remaining Tape TimeRecording of Stereo or Bilingual Programmes NV-HV60GL only Nicam Broadcast System NV-HV60GN onlyRecording from an external source Recording VCRVCR in tape refresh standby ModeTimer Recording Key ProgrammingTo Suspend the Timer Recording Standby Mode Setting other Programmes in SuccessionWeekly Timer Recording Daily Timer RecordingPress PROG/CHECK 14 twice Checking a Timer ProgrammeCancelling a Timer Programme Category setting allows you to To Set the CategoryRecorded by the character Icon indicationsWhen Recording Over the Same Location on a Tape To Cancel the Index Search or to Stop Playback Press StopTo Demonstrate the Jet Navigator Function To Check the Recorded Programming Data Time Stamp FunctionBefore Requesting Service To Cancel the Easy Programme PlaybackOperation Press Prog Play Message of On Screen DisplayDirt on the video heads Adjusting the Playback PictureCrystal View Control Specifications