– Other Functions –
Multi-Brand Remote Control
This Remote can control some functions of remote controllable TVs, cable boxes or DBS (Direct Broadcast Satellite) receivers listed below. Without setting, you can control a PANASONIC TV.
NOTES:
●Some unit’s brands have more than one code. If the unit does not function with a specified code, try other codes.
●Depending on the type of unit, some or all functions cannot be operated using this Remote.
●It’s not possible to operate a unit not equipped with a remote sensor.
●It’s not possible to set the Remote for both your cable box and a DBS receiver at the same time.
●Once you have set the Remote to operate the unit, you do not have to set it until you replace the batteries from the Remote.
TV Brand Setting
ATurn on TV
Turn on the TV using the Power button on the TV or its Remote.
BSet TV brand code
APress and hold TV. B Press MBR SET.
C Press the Number keys to enter your TV’s brand code. D Press OK, and release TV. The TV should turn off.
COperate TV
While holding down TV, press one of the following buttons: POWER, TV/VCR, TV
●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.
TV BRAND | CODE | TV BRAND | CODE |
|
|
|
|
PANASONIC | 04, 11 | SONY | 07 |
HITACHI | 10 | SAMSUNG | 12 |
JVC | 01, 03 | SANYO | 13 |
MAGNAVOX | 02 | SEARS | 13 |
MITSUBISHI | 03 | TOSHIBA | 08 |
RCA | 05 | ZENITH | 09 |
SHARP | 06 |
|
|
|
|
|
|
Cable Box or DBS Receiver Brand Setting
ATurn on cable box or DBS receiver
Turn on the cable box or DBS receiver using the Power button on the unit or its Remote.
BEnter brand code
APress and hold CABLE/DBS. B Press MBR SET.
C Press the Number keys to enter your cable box’s (or DBS receiver’s) brand code.
D Press OK, and release CABLE/DBS.
COperate cable box or DBS receiver
While holding down CABLE/DBS, press one of the following buttons: POWER, TV
●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.
●To change the cable box’s (or DBS receiver’s) channels, press TV CH+/– or the Number keys. (The CH+/– button can be used to change the VCR’s channels only.)
CABLE BOX BRAND | CODE |
|
|
PANASONIC | 13, 14 |
ARCHER | 01, 05, 17 |
CABLETENNA | 01, 17 |
CABLEVIEW | 15, 16, 17, 21, 25 |
CITIZEN | 15, 16, 17, 21, 25 |
CURTIS | 02 |
DIAMOND | 01, 17 |
EASTERN | 19 |
GC BRAND | 15, 16, 17, 21, 25 |
GEMINI | 15 |
GENERAL INSTRUMENTS | 01, 04, 06, 11, 12, 15, 28 |
HAMLIN | 10, 18, 19, 23 |
JASCO | 15 |
JERROLD | 01, 04, 06, 11, 12, 15, 28 |
NOVAVISION | 02 |
OAK | 07 |
PULSER | 15, 16, 17, 21, 25 |
RCA | 13, 14 |
REGAL | 10, 18, 19, 23 |
REGENCY | 19 |
REMBRANDT | 01, 16, 17 |
SAMSUNG | 05, 16, 24 |
SCIENTIFIC ATLANTA | 02 |
SIGMA | 07 |
SL MARX | 05, 16, 17, 24, 25 |
SPRUCER | 13, 14 |
STARGATE | 05, 15, 16, 17, 21, 24, 25 |
TELEVIEW | 05, 16, 24 |
TOCOM | 01, 04, 16 |
UNIKA | 01, 17 |
UNIVERSAL | 16, 17, 25 |
VIDEOWAY | 03, 09, 22 |
ZENITH | 03, 09, 22 |
|
|
DBS RECEIVER BRAND | CODE |
|
|
ECHOSTAR (DISH Network) | 51 |
JVC (DISH Network) | 51 |
PRIMESTAR | 50 |
SONY (DSS) | 41 |
RCA (DSS) | 40 |
|
|
Changing Remote Control Code
This Remote is capable of transmitting two control codes; one set to respond to A code control signals and another set to respond to B code control signals. This Remote control is preset to send A code signals because your VCR is initially set to respond to A code signals. You can easily modify your VCR and the Remote to respond to B code signals. When using two PANASONIC VCRs, set two VCRs and their Remotes to different codes, so that you can operate these VCRs separately.
ASet remote control code for Remote
APress and hold A/B.
BPress the Number key “2”. C Press OK, and release A/B.
● The Remote now can transmit B code control signals.
BCheck remote control code for VCR
Press and hold 4 on the VCR for more than 5 seconds while the VCR is turned off. The code currently set appears on the display panel.
CChange code for VCR
Press any key on the Remote. The VCR now responds to B code control signals.
●To set the Remote and the VCR back to A code control signals, repeat the same procedure as shown above except pressing the Number key “1” in step B of 1.
To control two VCRs with the same Remote
You can control two PANASONIC VCRs by switching the remote control code for the Remote between A and B ( step A), keeping two VCRs to different control codes.
●To change only the remote control code for the Remote, DO NOT perform steps B and C.
— 14 —