Hitachi VT-F382A owner manual Lmportantsafeguards

Page 7

i lMPORTANTSAFEGUARDS

7 Power Cord Protection -- Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

8 Ventilation -- Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the video product and to protect it from overheating. These openings must not be blocked or covered.

The openings should never be blocked by placing the video product on a bed, sofa, rug or other similar surface. This video product should never be placed near or over a radiator or heat register. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the video product manufacturer's instructions have been followed.

9 Attachments -- Do not use attachments unless recommended by the video product manufacturer as they may cause hazards.

Caution: Maintain electrical safetyl Power, line operated equipment or aCcessories connected to this unit should bear the UL listing mark 0rCSA certification mark on the access0ry itself and Should not have been modified

soas to defeat the safety features:This wi!! he!p avoid any potentia! hazard from electric shock or firel If in doubtl contact qualified service personnel.

10 Water and Moisture -- Do not use this video product near water -- for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

11 Accessories -- Do not place this video product on an unstable card, stand, tripod, bracket or table. The video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket or table recommended by the manufacturer, or sold with the video product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer.

11A An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

12 Outdoor Antenna Grounding -- If an outside antenna or cable system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper

Image 7
Contents VT-F382A Using these quality featuresH9RIB1 Canada VCR Display Indicators Meet Your On-Screen GuideProgramming Remote Control Controlling For Yoursafety Quick Index It Ei LMPORTANTSAFEGUARDS USE LMPORTANTSAFEGUARDS Hook up the AudioNideo Signal Decide Where to Put Your VCRDecide Which Hookup Method to Use TV with Audio and Video Jacks Hook up the RF SignalSimple Antenna/Cable 75 Ohm Hookup If you have Use this adapter External or Internal 300 Ohm AntennaAttach the TV and VCR to the Power Supply Set the RF or Video Channel Switch Install Batteries in the Remote ControlAbout the Illuminated Buttons How the Remote Control WorksGetting Started controls If You Just Want to Watch TV Display IndicatorsMeet Your On-ScreenGuide Getting Started Controls Initial Setup Options Setting the Clock Stereo vs. Mono Sound Choosing a Mode for Audio PlaybackMore About Channel Selections Removing ChannelsHi-Fi Sound Types Recording Time Safety Tabs Prevent ErasureTypes Tape Capacities at Different SpeedsTape Storage Direct Video Input to the TV To play Back a Recorded TapeTo Fine Tune the Picture Special Playback Effects Rewinding the TapeManual Rewind Movie ReturnTo Find Specific Sections on a Tape Visual Search Using the Shuttle Control on the remote controlSearching with the Time Counter Jump Forward or Backward with GO-TO Marking with the Time CounterJump to an Index Mark with Index Basic Operations Recording Tips To Watch the Same Program While Recording Before you RecordCopyright Infringement Warning Basic Recording StepsTo Record a Second Audio Program SAP Using the Instant Recording Timer IRTTo Change the Channel Being Recorded To Leave Index Marks on the TapeDaily Setting the VCR to Record LaterTypes of Delayed Recordings Delayed Recording StepsAn Example To Stop a Delayed Recording in ProgressShows with Different Starting Times Reviewing What You Have ProgrammedProgramming Priorities Shows with Same Starting TimeAbout VCR Plus+ Channel Setup Before You BeginBasic Operations VCR Plus + Recording Dilve Basic operations VCR Plus + Recording Basic Operations VCR Plus + Recording Weekly Recording Compatibility Programming the Remote ControlTV Brands Press IV and This Number Display NEC RCAJVC LastBasic hookup Position Cable BoxAdvanced hookup Cable Box to unscramble all channels AdVanced OperationsCable Box HookUps Recording from Your Stereo System HookupCopying from One VCR to Another Dubbing To Control Both VCRs with the Remote ControlSynchro Editing Hookup When VCR1 is RecordingCopying Tapes From a Camcorder Putting The Record VCR in PauseInformation on Audio Hookup Periodic Maintenance Head CleaningDont Attempt Repairs Yourself VHS Design and specifications subject to change without noticeProblem Things To Check Solution Often Encountered ProblemsDays a week, 24 hours a day Hitachi Service HotlineYou must state your zip code when calling Canada Continental U.S.A