JVC HR-VP780U manual TV Brand Setting, Turn on the TV, Set TV brand code, Operate TV

Page 45

MULTI-BRAND REMOTE CONTROL

EN 45

TV Brand

Setting

This Remote can control some functions of remote controllable TVs listed below. Without setting, you can control a JVC TV.

1 Turn on the TV

Turn on the TV using the Power button on the TV or its Remote.

2–14

TV

TV/VCR

4

7

1

			2–2
			POWER
2	3
5	6	2	2–3
8	9		Number
0		4

2Set TV brand code

Follow the example shown below.

1Press and hold TV.

2 Press MBR SET.

3 Press the Number keys to enter your TV’s brand code by referring to the table below.

4 Press OK, and release TV.

The TV should turn off. If it does, try other

operations below. ( step 3).

Once you have set the Remote to operate the TV, you do not have to set it until you replace the batteries from the Remote.

PANASONIC has two codes. If the TV does not function with one code, try entering the other.

3Operate TV

While holding down TV, press one of the following buttons: POWER, TV/VCR, TV CH +/–,

3

2–4

ENTER

TV VOL +/–

TV CH +/–

TV/VCR, (TV Muting), TV VOL +/–, and Number keys.

For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

NOTES:

Depending on the type of TV, some or all functions cannot be operated using this Remote.

It’s not possible to operate a TV not equipped with a remote sensor.

TV BRAND NAME	BRAND CODE
JVC	01, 03
HITACHI	10
MAGNAVOX	02
MITSUBISHI	03
PANASONIC	04, 11
RCA	05
SHARP	06
SONY	07
SAMSUNG	12
SANYO	13
SEARS	13
TOSHIBA	08
ZENITH	09

(Ex.) To set Remote to RCA 05:

	MBR SET
TV	A/B		ENTER/O
	0	5		SD
	0	5	3	OK
			3

Hold	Press in succession
down

Release

Image 45

Contents HR-VP780U Telephone Number Dear CustomerPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents Antenna Basic ConnectionsVideo OUT Back of VCRSituate VCR Check contentsConnect VCR to TV Final preparation for usePlug & Play Setting Perform Plug & Play setupWhat to do if Plug & Play setting failed Select language Language SettingReturn to normal screen Press MenuClock Setting 10 ENPreparations Set Auto Clock to on Setting clock semiautomaticallySelect host channel Select time zoneSelect D.S.T. mode Setting clock manually12 EN Manual Clock SetAccess Tuner Set screen Tuner SettingPerform Auto Channel Set Auto ChannelAccess Manual Channel Set screen Setting channels manually14 EN Add or skip desired channelsSituate Controller Cable Box Control SettingAttach Controller Connect cable box to VCRAccess Cable Box Set screen Access Main Menu screen on VCR16 EN Turn on cable boxAccessPress OKCable. Box Brand Set screen Enter cable box brandIf the cable boxs channel does not change to 18 EN How to control the DBS receiverConnect DBS receiver to VCR Connect Controller to VCRAccess DBS Receiver Set screen Turn on DBS receiverSelect DBS receiver output channel Access DBS Receiver Brand Set screen 20 ENEnter DBS Receiver’s brand Basic Playback Load a cassetteStart playback 22 EN Basic Playback FeaturesChanging display information Checking tape positionAdjusting tracking condition Selecting monitor soundAutomatic operations after Access distant code Locating beginning of timer24 EN Locating beginningRecording BasicSelect recording channel Set tape speed26 EN Basic Recording FeaturesSpecifying recording length Watching one program while recording anotherDisplay VCR status on TV screen Showing on-screen displayErase on-screen display Other useful functions for recording28 EN Special Effect PlaybackLocating particular scene Rapidly Picture Search High-Speed Picture SearchSkipping unwanted portions Viewing still pictureViewing slow motion picture Pause during playbackVCR Plus+ Timer Programing Daily Cancel30 EN To use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Press SP/EPVCR Plus+ Setup 32 ENVCR Plus+ guide channel matching Input guide channel number Access Guide Channel Set screen34 EN Express Timer ProgramingOFF To timer-record daily Monday-Friday or weekly serialsCatv DBS36 EN Checking program settingsConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen Change setting Useful Function Settings38 EN Select FunctionWhen this function is set to OFF When this function is set to onFor Example 40 ENLink Video This VCRVCR only Video OUT Pause AV Compulink 42 EN Edit From Camcorder Connection This VCR for recordingAccess Main Menu screen on this VCR Select input mode on this VCREnable remote pause function Make connectionsEdit To Or From Another Select input mode on recording VCR44 EN Load cassettesTurn on the TV TV Brand SettingSet TV brand code Operate TV46 EN Cable Box Brand SettingTurn on the cable box Enter cable box brand codeTurn on the DBS receiver DBS Receiver Brand SettingEnter DBS receiver brand code Operate DBS receiver48 EN Changing Remote Control CodePower 50 EN Timer RecordingOther Problems 52 EN Can the VCR indefinitely remain in still mode?What happens if the tape reaches its end during recording? VCR PLUS+ List of terms54 EN Front panelFront display panel On-screen display Rear panelHow to use the Remote 56 ENRemote Usable cassettes Full-Size VHS 30 ST-30Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40 58 EN HOW to Locate Your JVC Service CenterLimited Warranty HR-VP780U