JVC HR-J694EU, HR-J693EU, HR-J691EU specifications Link Functions, Satellite Receiver Control Set

Page 5

BSelect your country

Press rt to place the pointer next to your country, then press OK or e.

DConnect Satellite Controller to recorder

Connect the Satellite Controller to the SAT CONTROL connector on the rear panel.

CSelect language

Press rt to place the pointer next to the desired language.

You do not have to press OK; pressing OK enters AUTO SET/T-V LINK screen.

DReturn to normal screen

Press MENU.

T-V Link Functions

When you connect the recorder to your TV via a fully-wired

21-pin SCART cable, the following functions are available. You can use these functions only with a TV offering T-V Link, etc.* For details, refer to the instruction manual of your TV.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired

21-pin SCART cable. The degree of compatibility and available functions may differ by system.

NexTView Link

You can download the EPG (Electronic Programme Guide) information from your TV for timer-programming on the recorder.

TV Auto Power On

The TV will turn on and be set to its AV mode automatically whenever you play a tape.

VCR Auto Standby

You can use your TV’s remote control to turn off the recorder.

Direct Rec

You can easily start recording the programme that you are watching on your TV. When you use this function, set “DIRECT REC” to “ON”. ( 12)

Satellite Receiver Control Set

When you use an optional Satellite Controller and perform the following settings, you can control your satellite receiver’s channel for timer recording. Approximately 20 seconds before the timer recording starts, the recorder sets its input mode to “L-2” and the Satellite Controller switches the satellite receiver’s channels.

NOTE:

The Satellite Controller does not function for 24 Hour Express Timer Programming.

ASituate Satellite Controller

Place the Satellite Controller so that the path between its transmitter and the satellite receiver’s remote sensor is unobstructed.

BAttach Satellite Controller

Fix securely using the adhesive strip attached on the back of the Satellite Controller.

Satellite receiver

 

Satellite receiver

Transmitter

To VCR

 

 

connector

Satellite Controller

21-pin SCART cable

(not provided)

(not provided)

 

To L-2 IN/

 

DECODER

 

Your recorder

To SAT CONTROL

ETurn on satellite receiver

Turn on the satellite receiver’s power.

FAccess Main Menu screen, then Initial Set screen

Press MENU. Press rt to place the pointer next to “INITIAL SET”, then press OK or e.

GAccess Sat Control Set screen

Press rt to place the pointer next to “SAT CONTROL SET”, then press OK or e.

H Enter satellite receiver’s brand

Press the appropriate number keys to enter the brand code from the following list, then press OK.

If the code you entered is invalid, the code field will be reset. Enter the correct

code again.

BRAND NAME

CODE

BRAND NAME

CODE

 

 

 

 

JVC

73

MASPRO

70

AMSTRAD

60, 61, 62, 63, 92

NOKIA

87, 94

CANAL

81

PACE

65, 67, 74, 86, 92

SATELLITE

 

PANASONIC

74, 92

CANAL +

81

PHILIPS

66, 84, 101

D-BOX

85

RADIX

78

ECHOSTAR

82

RFT

69

(VIA DIGITAL)

 

SABA

97

FINLUX

68

SAGEM

83, 90

FORCE

89

SALORA

68

GALAXIS

88

SAMSUNG

83

GRUNDIG

64, 65, 102

SIEMENS

64

HIRSCHMANN

64, 78, 99

SKYMASTER

69, 98

HUMAX

88

TECHNISAT

66, 100

ITT NOKIA

68

THOMSON

97

KATHREIN

70, 71, 96

TPS

83

LUXOR

68

TRIAX

91

MASCOM

93

WISI

64

 

 

 

 

ISelect satellite receiver’s channel for testing

Press the appropriate number keys to enter the channel position on the satellite receiver, then press OK. The recorder enters the test mode.

Satellite Controller

Your recorder(not provided) (suggested locations)

CMake connections

Connect the recorder’s L-2 IN/DECODER connector to the satellite receiver’s 21-pin SCART connector.

J Check result of the test

If the satellite receiver’s channel number has been changed to the same one as you set in step 9 …

Press rt to place the pointer next to “CHANGED TO …”, then press OK or e to finish the Sat Control Set mode.

If the satellite receiver’s channel number has not been changed correctly …

Press rt to place the pointer next to “NOT CHANGED”, then press OK or e. Then perform the procedure again from step 8.

NOTE:

The Satellite Controller may not function properly with some types of satellite receiver.

— 5 —

Image 5
Contents For Italy Safety PrecautionsVideo heads cleaning How to use the remote controlFront Panel Rear PanelBasic Connections Remote controlOn-screen display RF ConnectionAuto Set Up Initial SettingsPreset Download Language SetSatellite Receiver Control Set Link FunctionsBasic Playback Playback FeaturesPlayback Basic Recording Recording FeaturesRecording Guide Program Number Set Showview System SetupSpecifying recording length Instant Timer Recording ITR Showview Timer Programming Timer RecordingExpress Timer Programming VPS/PDC RecordingChecking, canceling or changing programme settings System Connections EditingMode Set Subsidiary SettingsSelect mode Change settingAuto Channel Set Clock SetTuner Set Manual Channel Set When receiving a scrambled broadcastDeleting a channel Changing station channel positionsChanging station name a Fine-tuning channelsChanging station name B TV station and ID listVideo Channel Set Specifications