JVC HR-J696EK, HR-J695EK manual Other Problems

Page 57

subsidiary information

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

57

TIMER RECORDING (cont.)

• The loaded cassette has had its

7. U, ,and the SATcindicator

won’t stop blinking.

record safety tab removed.

Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.

8.Uand ,on the display panel won’t stop blinking.

The end of the tape was reached during Auto Satellite Programme Recording.

The end of the tape was reached during Instant Timer Recording.

The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

OTHER PROBLEMS

1.Whistling or howling is heard from the TV during camcorder recording.

2.When scanning channels, some of them are skipped over.

3.The preset cannot be changed.

4.Channel settings that were made manually seem to have changed or disappeared.

5.No channels are stored in the VCR’s memory.

The camcorder’s microphone is too close to the TV.

The TV’s volume is too high.

Those channels have been designated to be skipped.

Recording is in progress.

After the manual settings were made, Auto Channel Set was performed.

The TV aerial cable was not connected to the VCR when Auto Set Up was performed.

The fully-wired 21-pin SCART cable was not connected between TV and the VCR when Preset Download was per- formed.

Position the camcorder so its microphone is away from the TV. Turn the TV’s volume down.

If you need the skipped channels, restore them.

Press to pause the recording, change presets, then press .to resume recording.

Perform manual setting again.

Turn off the VCR once and connect the TV aerial cable to the VCR properly, then turn on the VCR again. Then perform Auto Setup again (pg. 10).

Turn off the VCR once and connect the fully-wired 21-pin SCART cable to the VCR properly, then turn on the VCR again. Then perform Preset Download again

(pg. 11).

Image 57
Contents HR-J695EK HR-J696EK Blue to N Neutral or Black Brown to L Live or Red Safety PrecautionsMoisture Condensation On The Safe Use Of Equipment Some Do’s And Don’tsContents Front panel Front Panel Diagram KeyGetting Everything Ready Welcome to JVCPerform Auto Setup pg Three-Step Quick Start Auto SetupPreset Download Finish Off Check the ResultsGo straight to 2000 used as example only Perform Clock Set on Go to StepBasic Features Load a Video Cassette PlaybackPlay Stop & EjectRewind and Fast Forward Video Heads CleaningPlayback Features Pause During PlaybackSingle Frame Movement Slow Motion Variable Speed SearchHigh Speed Search Choose a Programme RecordingSet the Tape Speed Start RecordingResetting the Counter Display Tape Remaining TimeChange Display Information Recording Resume Function Instant Timer RecordingGet to the Video Plus + Screen Enter the PlusCode NumberPress p. You will see the following TV screen information Return to Normal Screen Engage Timer Mode Express Timer Programming Get to the Programme ScreenEnter Programme Details AUX Check, Cancel & Change Programmes Press c, then press oto disengage the timer modeTimes as necessary Advanced Features Picture Quality Manual TrackingPicture Control Avoiding B.E.S.T. Time Delay Recording and Playback Using B.E.S.TB.E.S.T Picture System Turning B.E.S.T. on or OFFSound Modes Nicam Stereo and Bilingual BroadcastsSoundtrack Selection Skip Search Finding Specific ScenesIndex Search Instant ReViewYou can use your TV’s Remote Control to turn off the VCR TV Auto Power OnLink Functions NexTView LinkDirect Rec Buttons. Press Or E to select on orRecording on Installing Satellite Controller Satellite Receiver Control SettingsSET using the Aand Bbuttons. Press Or E Setting satellite receiver’s brandAppropriate number keys to enter the brand ModeOr E to finish the Sat Control Set mode Check Result of TestPress the Aand Bbuttons to move Auto Record from Satellite Receiver Auto SatelliteAdvanced features Editing Editing Using Another VCRStart recorder Press T Editing from a CamcorderOn-Screen Display O.S.D Other FunctionsAuto SP aLP Timer Power Save ModeAuto Power Off/3H Auto TimerRepeat Playback Next Function MemoryAUX in or Tape Monitor Connection to a Stereo SystemExit Video Channel Set Mode Access Video Channel ModeVideo Channel Set Set Video ChannelSET using the Aand Bbuttons and press Or E twice Auto Channel SetupTuner Set Perform auto channel set Move the highlight bar to Auto CHButton on the Remote Control to move the highlight bar Manual Channel SetupPress Or E Confir- onwards asChange Station Name To the preset position you want then pressDelete a Channel Confirmation screen appearsButton on the Remote Control until the item you want to Change Station Preset PositionButton to move the station to the new preset position Then pressTV Station ID Guide Fine-Tuning Stored ChannelsBBC1 BBC2 ITV CH4 CH5 TV Station Channel Number GuideSetting the Clock Or E. The dateOr E. Set the correct year Guide Program Numbers Manually Setting Guide Program NumbersQuestion and Answers Uand cremain lit on the display panel. Is there a problem?Can the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?Symptom Possible Cause TroubleshootingRecording Other Problems List of Terms Memo HR-J695/696EK