JVC HR-S4800U manual 18 EN, Connect DBS receiver to VCR, How to control the DBS receiver

Page 18

18 EN

INITIAL SETTINGS (cont.)

DBS Receiver Control Setting

Suggested location

Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR’s Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver’s remote sensor.

ATTENTION:

The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the Controller so its signal reaches the remote sensors on both the DBS receiver and cable box.

DBS receiver

Controller

Your VCR(suggested

locations)

DBS receiver

Controller

 

 

To

 

To

RF output

 

Audio/Video

Transmitter

 

output

or

To

To

 

 

AUDIO/

ANTENNA IN

 

VIDEO IN

Your VCR

CABLE

BOX

The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) receiver. The Controller allows the VCR to automatically switch the DBS receiver’s channels during timer recording.

NOTES:

c ONLY FOR HR-S3800U: The Controller is not supplied with this unit. It can be requested by mailing in the completed JVC Cable Mouse Certificate that is included with the accessory package.

c The VCR can automatically change the DBS receiver channels using the Controller when the VCR has been programed using Express timer programing (Z pg. 34). Because satellite programing does not use PlusCode, the Controller cannot change the DBS receiver channels during VCR Plus+ timer recording.

c If a cable box is also used, it is recommended that you connect the DBS receiver to your VCR’s audio/video input connectors and the cable box to your VCR’s antenna input terminal.

Installing Controller

1

Situate Controller

Place the Controller so that its transmitter is

 

facing the DBS receiver’s remote sensor.

 

c Make sure the path between the Controller and

 

the DBS receiver’s remote sensor is not

 

blocked.

2

 

Attach Controller

 

Fix securely using the adhesive strip attached on

 

 

the back of the Controller.

3

 

 

 

Connect DBS receiver to VCR

 

c If your DBS receiver does not have audio/

 

 

 

 

videooutputconnectors

 

 

Connect the RF output terminal on the DBS

 

 

receiver to the ANTENNA IN terminal on the

 

 

rear of your VCR.

 

 

c If your DBS receiver has audio/video output

 

 

connectors

 

 

Connect an audio/video cable between the

 

 

AUDIO/VIDEO IN connectors on the rear of

 

 

the VCR and the audio/video output connectors

 

 

on the DBS receiver.

 

 

NOTE:

 

 

When connecting your DBS receiver, refer to its

 

instruction manual.

4

 

 

 

Connect Controller to VCR

 

Connect the Controller to the CABLE BOX

Controller connector on the rear panel.

How to control the DBS receiver

This VCR has two separate methods to control your DBS receiver.

c The VCR’s wireless Remote can control your DBS receiver. This eliminates the need for a separate DBS receiver’s Remote.

c The VCR’s Controller can also control your DBS receiver. This allows the VCR to change your DBS receiver’s channel number during timer-recording.

Each method must be set up separately. To set up the VCR’s Remote, refer to page 52. To set up the Controller, go to page 19.

HR-S4800U/S3800U-EN01-20

18

00.1.31, 9:55 AM

Page 17 Page 19
Image 18
Page 17 Page 19
Contents HR-S4800U HR-S3800U Dear Customer TelephoneNumberPower Lines Power SourcesPower Cord Protection Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Basic Connections Back of VCRSituate VCR Check contents Final preparation for useConnect VCR to power source Connect VCR to TVWhat to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup Clock and tuner channels will be set automaticallyAccess Initial Set screen Language SettingAccess Main Menu screen Select languagePreparations Clock Setting10 EN Select clock setSet Auto Clock to on Setting clock semiautomaticallySelect D.S.T. mode Select time zoneSetting clock manually 12 ENTuner Setting Access Tuner Set screenPerform Auto Channel Set 14 EN Setting channels manuallyAccess Manual Channel Set screen Manual Channel SetAttach Controller Cable Box Control SettingSituate Controller Connect cable box to VCR16 EN Access Main Menu screen on VCRAccess Cable Box Set screen Turn on cable boxAccess Cable Box Brand Set screen Enter cable box brandHow to control the DBS receiver 18 ENConnect DBS receiver to VCR Turn on DBS receiver Access DBS Receiver Set screenAccess Main Menu screen on VCR Select DBS receiver output channelEnter DBS Receiver’s brand Access DBS Receiver Brand Set screen20 EN If the DBS receiverÕs channel does not change asshownaboveBasic Playback Load a cassetteChanging display information Basic Playback Features22 EN Checking tape positionAdjusting tracking condition Selecting monitor soundAutomatic operations after 24 EN Locating beginning of timerAccess distant code Locating beginningSet tape speed Basic RecordingSelect recording channel Start recordingSpecifying recording length Basic Recording Features26 EN Watching one program while recording anotherDisplay VCR status on TV screen Select S-VHS ET modeShowing on-screen display Exit on-screen displayLocating particular scene Special Effect Playback28 EN Rapidly Picture Search High-Speed Picture SearchViewingframe still picture frame by Viewing still pictureSkipping unwanted portions Viewing slow motion picture30 EN VCR Plus+ Timer ProgramingAccess VCR Plus+ screen Enter PlusCode numberInput receiving channel number To use the VCR while it is in timer recording standby modeEngage timer recording standby mode Check program dateChanging VCR Plus+ Setting 32 ENVCR Plus+ guide channel matching To Guide Channel Access Guide Channel Set screenInput guide channel number To move the highlight bar arrow to GuideSet program stop time Express Timer Programing34 EN Set program dateEngage timer recording standby mode To timer-record daily Monday-Friday or weekly serialsChecking program settings 36 ENOverlapping programs blink on the screen Confirm overlapping programsSelect program to modify Press Shuttle Plus %Þ, then press Shuttle Plus #38 EN Useful Function SettingsChange setting Select FunctionPicture Control Auto TimerVideo Calibration SuperimposeVideo Stabilizer Auto SP = EP Timer40 EN Blue BackVHS Mode AV COMPU-LINKRear AUX Input 42 ENFront AUX Input Edit FunctionCannot turn on the VCR by pressing Power on Child LockChild lock function is now activated and you Connection Edit From Camcorder44 EN Various connection for editing tapesSet AV COMPU-LINK to OFF Select input mode on this VCRMake connections Start playbackEdit To Or From Another Select edit modeSelect input mode on recording VCR 46 ENSet Edit Function to A. DUB Source Select input modeAudio Dubbing Locate start pointAnother VCR for playback 48 ENInsert Editing Sourcetape Editedtape AV Dubbing Sourcetape EditedtapeSelect editing function you want Activate editing modePrepare tapes Start editingTurn on the TV TV Brand Setting50 EN Set TV brand codeEnter cable box brand code Cable Box Brand SettingTurn on the cable box Operate cable boxTurn on the DBS receiver DBS Receiver Brand Setting52 EN Enter DBS receiver brand codeUnplug VCR Changing Remote Control CodeSet remote control code for Remote Plug in VCRTroubleshooting 54 ENTimer Recording Other Problems 56 ENCan the VCR indefinitely remain in still mode? Can the VCR indefinitely remain in the recording pausemode?What happens if the tape reaches its end during recording? Brand Installing the Controller 18 Output channel Brand Installing the Controller 15 Output channelManual setting Preparation Semiauto setting 58 ENFront panel Front display panel60 EN Rear panelOn-screen display How to use the Remote Remote62 EN UsablecassettesHOW to Locate Your JVC Service Center Limited Warranty 64 ENMemo 66 EN HR-S4800U/S3800U-EN54-68 00.1.31, 1005 AM HR-S4800U/S3800U
Related manuals
Manual 2 pages 57.65 Kb
Top Page Image Contents