JVC HR-S4800U manual 20 EN, Access DBS Receiver Brand Set screen, Enter DBS Receiver’s brand

Page 20

DBS RECEIVER BRAND SET

51

DID YOUR DBS RECEIVER CHANGE TO CHANNEL 100? =YES

NO

PRESS (5,°), THEN (OK)

PRESS (MENU) TO END

DBS RECEIVER BRAND SET

4 0

PRESS NUMBER KEY (0–9)

THEN (OK) TO TEST PRESS (MENU) TO END

20 EN

INITIAL SETTINGS (cont.)

POWER

S-VIDEO

VIDEO (MONO)L—AUDIO—R

S-VHS ET	SP	EP
S-VHS ET		VCR

	6
	REW		FF
	MENU
		PLAY
CH	REC	STOP/EJECT	PAUSE
	OK

6

7

Access DBS Receiver Brand Set screen

Press OK.

Enter DBS Receiver’s brand

On the Remote ONLY:

Press the appropriate Number keys to enter the brand code from the following list, then press OK.

The program currently received through the

DBS receiver appears for about 10 seconds.

BRAND	CODE
JVC (DISH Network)	51
ECHOSTAR (DISH Network)	51
PRIMESTAR	50
SONY (DSS)	41
RCA (DSS)	40

1 2 3

2

4 5 6 7

7 8 9

0 4

1

6 7

cIf the DBS receiverÕs channel changes to the channel listed below for your brand, setting is complete

JVC =100 ECHOSTAR =100 PRIMESTAR = 55 SONY =205 RCA =205

Press OK and “DBS

RECEIVER CONTROL IS ON” appears on the screen for about 5 seconds, then it returns to the normal screen.

cIf the DBS receiverÕs channel does not change asshownabove

1 Press SHUTTLE PLUS %Þ (or CH 5° on the front panel) to move the highlight bar

(arrow) to “NO”.

2Press OK.

3Re-enter the correct code.

NOTES:

c The Controller may not work with all types of DBS receiver. c If your DBS receiver does not respond to the code, you

cannot use the Controller to change satellite channels. In this case, make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start time of timer recording.

c The VCR can only change the satellite channel through the Controller during timer recording.

c If your DBS receiver cannot be operated with a remote control (because it has no remote sensor), you cannot use the Controller to change its channels. Make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start time of timer recording.

cFor customers in U.S.A.: If you are unable to set the Controller, contact JVC toll free at 1-800-252-5722.

HR-S4800U/S3800U-EN01-20

20

00.1.31, 9:55 AM

Image 20

Contents HR-S4800U HR-S3800U Dear Customer TelephoneNumberPower Sources Power Cord ProtectionPower Lines Grounding or PolarizationAccessories Damage Requiring ServiceCleaning Replacement PartsContents Basic Connections Back of VCRCheck contents Final preparation for use Connect VCR to power sourceSituate VCR Connect VCR to TVPlug & Play Setting Perform Plug & Play setupWhat to do if Plug & Play setting failed Clock and tuner channels will be set automaticallyLanguage Setting Access Main Menu screenAccess Initial Set screen Select languageClock Setting 10 ENPreparations Select clock setSetting clock semiautomatically Select D.S.T. modeSet Auto Clock to on Select time zoneSetting clock manually 12 ENPerform Auto Channel Set Tuner SettingAccess Tuner Set screen Setting channels manually Access Manual Channel Set screen14 EN Manual Channel SetCable Box Control Setting Situate ControllerAttach Controller Connect cable box to VCRAccess Main Menu screen on VCR Access Cable Box Set screen16 EN Turn on cable box Access Cable Box Brand Set screen Enter cable box brandConnect DBS receiver to VCR How to control the DBS receiver18 EN Access DBS Receiver Set screen Access Main Menu screen on VCRTurn on DBS receiver Select DBS receiver output channelAccess DBS Receiver Brand Set screen 20 ENEnter DBS Receiver’s brand If the DBS receiverÕs channel does not change asshownaboveBasic Playback Load a cassetteBasic Playback Features 22 ENChanging display information Checking tape positionAutomatic operations after Adjusting tracking conditionSelecting monitor sound Locating beginning of timer Access distant code24 EN Locating beginningBasic Recording Select recording channelSet tape speed Start recordingBasic Recording Features 26 ENSpecifying recording length Watching one program while recording anotherSelect S-VHS ET mode Showing on-screen displayDisplay VCR status on TV screen Exit on-screen displaySpecial Effect Playback 28 ENLocating particular scene Rapidly Picture Search High-Speed Picture SearchViewing still picture Skipping unwanted portionsViewingframe still picture frame by Viewing slow motion pictureVCR Plus+ Timer Programing Access VCR Plus+ screen30 EN Enter PlusCode numberTo use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Check program dateVCR Plus+ guide channel matching Changing VCR Plus+ Setting32 EN Access Guide Channel Set screen Input guide channel numberTo Guide Channel To move the highlight bar arrow to GuideExpress Timer Programing 34 ENSet program stop time Set program dateEngage timer recording standby mode To timer-record daily Monday-Friday or weekly serialsChecking program settings 36 ENConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen Press Shuttle Plus %Þ, then press Shuttle Plus #Useful Function Settings Change setting38 EN Select FunctionAuto Timer Video CalibrationPicture Control SuperimposeAuto SP = EP Timer 40 ENVideo Stabilizer Blue BackVHS Mode AV COMPU-LINK42 EN Front AUX InputRear AUX Input Edit FunctionChild lock function is now activated and you Cannot turn on the VCR by pressing Power onChild Lock Edit From Camcorder 44 ENConnection Various connection for editing tapesSelect input mode on this VCR Make connectionsSet AV COMPU-LINK to OFF Start playbackSelect edit mode Select input mode on recording VCREdit To Or From Another 46 ENSource Select input mode Audio DubbingSet Edit Function to A. DUB Locate start point48 EN Insert Editing Sourcetape EditedtapeAnother VCR for playback AV Dubbing Sourcetape EditedtapeActivate editing mode Prepare tapesSelect editing function you want Start editingTV Brand Setting 50 ENTurn on the TV Set TV brand codeCable Box Brand Setting Turn on the cable boxEnter cable box brand code Operate cable boxDBS Receiver Brand Setting 52 ENTurn on the DBS receiver Enter DBS receiver brand codeChanging Remote Control Code Set remote control code for RemoteUnplug VCR Plug in VCRTroubleshooting 54 ENTimer Recording Other Problems 56 ENWhat happens if the tape reaches its end during recording? Can the VCR indefinitely remain in still mode?Can the VCR indefinitely remain in the recording pausemode? Brand Installing the Controller 15 Output channel Manual setting Preparation Semiauto settingBrand Installing the Controller 18 Output channel 58 ENFront panel Front display panelOn-screen display 60 ENRear panel How to use the Remote Remote62 EN UsablecassettesHOW to Locate Your JVC Service Center Limited Warranty 64 ENMemo 66 EN HR-S4800U/S3800U-EN54-68 00.1.31, 1005 AM HR-S4800U/S3800U

Related manuals

Manual 2 pages 57.65 Kb