JVC HR-S4600U instruction manual Recording Features

Page 34

34EN

PLAYBACKANDRECORDINGFEATURES(cont.)

Recording

Features

JOG

SHATTLE

 

 

TV/VCR

 

 

(HR-S3600U only)

V/VCR

 

OSD

 

 

DISPLAY

1

2

3

 

 

2

4

5

6

7

8

9

C.RESET

0

4

 

 

1

Record One Program While Watching Another

1

ENGAGE TV MODE

During recording...

 

Press TV/VCR. The VCR's VCR indicator goes out. (If

you are using the RF connection (

pg. 6) to view

 

the output from your VCR, the TV broadcast being

 

recorded disappears.)

 

 

If you are using the AV connection (

pg. 6) to view

 

the output from your VCR, change the TV's input

 

mode from AV to TV.

 

SELECT CHANNEL FOR

VIEWING

2 Use the TV’s channel selector to set the channel you want to watch.

Display Elapsed Recording Time

RESET COUNTER TO ZERO

1 Before recording starts, press C.RESET. The counter resets to zero and displays the exact elapsed time as the tape runs.

DISPLAY ELAPSED TIME ON SCREEN

2 During recording, press OSD at any time to see the elapsed time.

All indications corresponding to the current status of the VCR are displayed for 5 seconds. The counter display remains on the screen indicating the elapsed time. Press OSD again to remove the display.

Make sure "SUPERIMPOSE" is set to "ON" ( pg. 29). The indications are not recorded.

Press DISPLAY to change to the COUNT display if "REMAIN" is displayed.

Display Tape Remaining Time

DISPLAY COUNTER

INFORMATION

1 Press OSD.

All indications corresponding to the VCR's current status are displayed for 5 seconds. The counter display remains on the screen indicating the elapsed time.

DISPLAY TAPE REMAINING TIME

2 Press DISPLAY until "REMAIN" appears on screen. The approximate tape remaining time appears on the TV screen and also on the VCR display panel with a "" indicator.

The tape remaining time is calculated based on the tape speed (SP or EP) being used. The indicated remaining time is only an estimate.

Press DISPLAY to change the on-screen display from REMAIN to COUNT and vice versa; and to show counter reading, channel number, clock time or tape remaining time on the front display panel. Then channel number will not be displayed when the VCR is playing a tape.

EXIT THE DISPLAY

3 Press OSD again.

NOTES:

"SUPERIMPOSE" must be set to "ON", or the on-screen display will not appear ( pg. 29).

Near the beginning of the tape, the tape remaining estimate may be inaccurate. However, the estimate becomes more accurate as the tape comes closer to the end.

Depending on the type of tape used, the tape remaining time reading may not appear right away, or may not be correct. "- -:- -" may sometimes appear, or the display may blink on occasion. The tape remaining time indication is not accurate when using VHS-C tapes with VHS-C adapter.

Page 33 Page 35
Image 34
Page 33 Page 35
Contents HR-S4600U HR-S3600U Dear Customer Do not place the VCRPower Lines Power SourcesPower Cord Protection Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Connections Matching Transformer Back of VCRCoaxial Cable RF Cable suppliedEN I Nitial Sett Ings Plug & Play SetupPlug & Play Auto Clock Set/Auto Tuner SetInformation Language Preparation Access Clock SETClock Pressing Shuttle PlusSelect Host Channel Select D.S.T. ModeSET Auto Clock to on Semi-AutoSET Time Select Time ZoneReturn to Normal Screen SET DateSET Access Main Menu ScreenTuner Set Receivable ChannelsChannel Access ManualAdd Or Delete a Channel Attach Controller Cable Box ControlSituate Controller Connect Cable BOX to VCRTurn on Cable BOX Access Cable BOX SETAccess Initial SET Screen Select Cable BOX Output ChannelEnter Cable BOX Brand Access Cable BOX Brand SET ScreenBrand Code Connect DBS Receiver To VCR DBS Receiver ControlDBS receiver Select DBS Receiver Access DBS Receiver SETTurn on DBS Receiver Output ChannelDBS Receiver Code from Following list, then Press OK Access DBS ReceiverSET DBS Receiver Brand JVC Dish Network Echostar Dish NetworkFind Program Start Point Simple PlaybackLoad a Cassette Start PlaybackSimple Recording Frame Playback Playback FeaturesActivate FRAME-BY EN Playba CK a ND Recording Feat UresAdjust Manual Tracking Access Distant CodeEngage Manual Tracking Mode Start SearchLayback and Recording Features Access Function SETSET Mode Picture ControlVideo Stabilizer Select The SoundtrackFront AUX Input Start Repeat Stop RepeatSuperimpose ModeSelect Superimpose SET Perform Movie Access Skip MenuSelect Mode AdvanceAV Compu Link Playback ExampleActive Video Calibration Playback and Recording FeaturesVideo Calibration Recording PlaybackStart Playback Recording Features VHS Super VHS, S-VHS ET and VHS Select S-VHS ET SET Layba CK and Recording FeaturesSuper VHS ET Second Audio Program Stereo And SAPTo Record SAP Programs Input Receiving Channel Number VCR Plus+ Timer ProgrammingEN Timer Recording Enter Pluscode NumberEntered and the matching Timer-Recording informaPlusCode number you Tion is displayed onVCR Plus+ Guide Channel Matching VCR Plus+ SetupInitial SET, then press Input Guide Channel Number Access Guide Channel SET ScreenThen press OK or Shuttle SET Program Date Express Timer ProgrammingAccess VCR PLUS+ SET Channel NumberEngage Timer Mode Check, Cancel And Revise Programs Cancel or Revise aRE-ENGAGE Timer ProgramAuto Timer Select Auto SP EP Timer SET ModeAuto SP→EP Timer Or Shuttle PlusSET Recording Duration Instant Timer Recording ITREngage ITR Mode Press REC on the front panelAutomatic Sat- ellite Program Recording Engage Auto Satellite Prog REC ModeBefore performing the following steps Recorder Edit From a CamcorderEditing PlayerFront AUX Input appears only with HR-S4600U Pause connector whenSet your VCR to its record mode Plus %Þto moveEdit To Or From Another Engage Audio Dubbing Audio DubbingLocate Start Point Start DubbingLocate END Point Reset the CounterInsert Editing EN EditingStart Editing END Insert EditingSET TV Brand Code TV Multi-Brand Remote ControlTurn on the TV Operate TVOperate Cable BOX Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Cable BOX Brand Name Brand CodeTurn on the DBS Receiver EN Special FeaturesDBS Receiver Multi-Brand Remote Control Enter DBS Receiver BrandSET Remote Control Turn VCR Power onUnplug Vcrs Power Plug in Power CordCassette gets stuck partway Make sure the cassettes window isRe-perform the VCR Plus+ setup Doesn’t work properly Timer againProcedure Those in the previous area Troubleshooting Other ProblemsCan the VCR indefinitely remain in the Record-Pause mode? Questions and Answer S E NCan the VCR indefinitely remain in the still mode? What happens if the tape runs out during recording?List Of Terms Express Timer ProgrammingMBR Multi-Brand Remote Code Setting IndexFront View HR-S4600U EN Index Rear ViewRemote Control Year programmable timer 20C to 60C -4F to140FHOW to Locate Your JVC Service Center For Servicing Only in U.S.AWarranty Only in U.S.A Limited WarrantyMemo Memo Memo HR-S4600/S3600U
Top Page Image Contents