JVC HR-S5600AM Access Tuner SET, Access Channel List, Select Position, SET Desired Station

5	SELECT TV SYSTEM
	Press PUSH JOG %Þ to					TV SYSTEM SELECT
	place the pointer next to						B/G
	the appropriate TV system,
							D/K
	then press OK or PUSH						I
	JOGÞ.						M
	● Auto Channel Set will				[5/°] =
		start.			[MENU] : EXIT
					CH	FRQ	SYS	CH	FRQ	SYS
					01	150	BG	07	229	BG
			AUTO CH SET		02	165	BG	08	237	BG
					03	195	BG	09	355	BG
			PLEASE WAIT		04	205	BG	10	365	BG
					05	213	BG	11	374	BG
					06	221	BG	12	384	BG
	START			FINISH	[5/°] =[CANCEL] : DELETE
					[5/°] =		: EDIT
					[MENU] : EXIT
	RETURN TO NORMAL
6	SCREEN
	Press MENU.

NOTE:

If you perform Auto Channel Set when the aerial cable is not connected properly, "SCAN COMPLETED -NO SIGNAL-" appears on the screen in step 5. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again.

IMPORTANT

●If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Channel Set, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels. ☞ "TV System Selection – When you see the picture but the audio can't be heard or sounds unnatural" on page 45.

●Since your video recorder memorizes all detected stations even if the reception condition is poor, some of those stored stations may produce a noisy picture. To delete those stations, ☞ "Delete A Channel" on page 44.

Major Countries	TV System
Australia, New Zealand, Kuwait, U.A.E.,
Indonesia, Singapore, Thailand, Malaysia,	B/G
Iran, Saudi Arabia, Egypt, Morocco,
Lebanon, Iraq
China, Mongolia, Russia	D/K
Hong Kong	I
U.S.A., Japan, S.Korea, Taiwan	M

EN43

Manual Channel Set

Store channels that were not stored during Auto Set Up (☞ pg. 8) or Auto Channel Set (☞ pg. 42).

	ACCESS TUNER SET
	SCREEN
1 Perform steps 1 – 3 of "Auto Channel Set" on page 42.
2	ACCESS CHANNEL LIST
	Press PUSH JOG %Þ to place the pointer next to "CH
	EDIT", then press OK or PUSH JOGÞ.
	SELECT POSITION
	Press PUSH JOG %Þ to place the pointer next to an
3 open channel position, then press OK or PUSH JOGÞ.
4	SELECT BAND
	Press PUSH JOG %Þ to place the pointer next to the
	band of your choice, then press OK to initiate Manual
	Channel Set.		MANUAL CH SET
		BAND SELECT
		VHF L	PLEASE WAIT
		VHF H
		UHF	VHF L 100MHZ
	[5/°] =		[MENU] : EXIT
		[MENU] : EXIT
		SET DESIRED STATION
	The screen to the right
	appears when a station is		STORE
5 detected.			CONTINUE
	If you do not want to store
	the detected station...
	Press PUSH JOG %Þ to
	place the pointer next to		[5/°] =
	"CONTINUE", then press		[MENU] : EXIT
	OK or PUSH JOGÞ.
		Channel search will resume.
	If you want to store the detected station...
	Press PUSH JOG %Þ to place the pointer next to
	"STORE", then press OK or PUSH JOGÞ. The Channel
	List appears again.

●The blueback screen and the TV picture currently being broadcast appear alternately for 8 seconds each.

●If you want to store another channel, repeat steps 3 – 5.

●When channel search completes for that band, the Band Select screen appears again. To set channels for other bands, select another band and start Manual Channel Set again (☞ step 4 and 5).

●For fine tuning adjustment, see "Fine-Tuning Channels" on page 45.

RETURN TO NORMAL

SCREEN

6 Press MENU.