JVC HR-S5902/5912U specifications Other Functions, Timer warning display, Checking tape position

PR START STOP CH DATE

1 8:00P 10:00 12 12/24

2 10:00A 10:45 40 12/25

3 11:30P 1:00 125 12/25

4 9:00P 10:00 10 12/24

5

6

7

8

( , ) THEN ( ) (PROG.) : END

–WARNING–

TIMER RECORDING TO START SOON

(CANCEL)

Program overlap warning display

If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking.

	PR START		STOP	CH	DATE
PROGRAM NOT COMPLETED	1	8:00P	10:00	12	12/24
	2	10:00A	10:45	40	12/25
PROGRAM OVERLAP	3	11:30P	1:00	125	12/25
	4	9:00P	10:00	10	12/24
	5
	6
	7
	8
	(	, ) THEN ( ) (PROG.) : END

Example:

Other Functions

Timer warning display

A warning appears on the TV screen to tell you that the timer-recording is to start in 5 minutes if you are not in the timer recording standby mode at that time. Press TIMER to put the VCR into timer recording

standby mode. To clear the display, press CANCEL on the Remote.

Checking tape position

Program 1 (you have just made) and Program 4 overlap each other

A Select program to modify

Press rt, then press OK or e.

● You can only select one of the overlapping programs.

● If you do not mind this overlap, press PROG. to finish the timer program setting. The program starting earlier or

program with the lower program number will be recorded.

When you change the VCR operation mode from the stop mode to fast forward

or rewind mode, or when you perform an B + Index Search ( pg. 10) or Instant Review

( pg. 10), the tape position indicator appears.

The position of “q” in relation to “B” (Beginning) or shows you where you are on the tape.

●Set “SUPERIMPOSE” to “ON” ( pg. 15).

+	+		E
REMAIN		1:00
COUNT		– 1:23:45

“E” (End)

B Cancel or change program setting		PROGRAM 4
To cancel a program, press CANCEL when	START	STOP
the Program screen you do not want is	9:00PM	10:00PM
	DATE	CH
shown.	12/24/03	10 SP
	WED
To change a program, press the
	PRESS (CANCEL) TO CANCEL
appropriate button: START+/–, STOP+/–,	PRESS (OK) TO CONFIRM
	PRESS (PROG.) TO END
DATE+/–,CH+/–,DAILY (M-F) (Number

key “8”), WEEKLY (Number key “9”) and/or SP/EP when the Program screen on which you want to make changes is shown, then press OK or e.

●If the overlap is not yet solved, the conflicting programs will be shown on the Program check screen. Repeat the above steps again.

Changing display information

Each time you press DISPLAY, the display panel shows the channel number and the clock time alternatively. ● You can change display in the stop or recording

mode, or during rewind/fast-forward. ● When “SUPERIMPOSE” is set to “ON”

( pg. 15) and DISPLAY on the Remote is pressed, time counter and tape remaining time will appear on the TV screen. To reset the time counter, press C.RESET on the Remote.

Function settings

You can use the other useful function settings on the Function Set screen.

A Access Main Menu screen, then	MAIN MENU
Function Set screen
	TUNER SET
	FUNCTION SET
Press MENU on the Remote. Press rtto	INITIAL SET
move the highlight bar (arrow) to
“FUNCTION SET”, then press OK or e.
	PRESS ( , ), THEN (OK)
B Select Function	PRESS (MENU) TO END

Press rtto move the highlight bar (arrow) to the function you want to set.

FUNCTION		PREVIOUS PAGE		PREVIOUS PAGE
S-VHS ET	OFF	VIDEO STABILIZER	OFF	FRONT AUX INPUT	VIDEO
VIDEO CALIBRATION	ON	BLUE BACK	ON	REAR AUX INPUT	VIDEO
PICTURE CONTROL	AUTO	2ND AUDIO RECORD	OFF
AUTO TIMER	OFF	AUDIO MONITOR	HI-FI
SUPERIMPOSE	ON	S-VHS MODE	ON
AUTO SP EP TIMER	OFF	AV COMPU-LINK	ON
NEXT PAGE		NEXT PAGE
SELECT WITH ( , ) AND (OK)		SELECT WITH ( , ) AND (OK)		SELECT WITH ( , ) AND (OK)
PRESS (MENU) TO END		PRESS (MENU) TO END		PRESS (MENU) TO END

CChange setting

Press OK or e. The default setting is bold in the table below. Press MENU to return to normal screen.

After a power failure occurs, Function Settings will be reset to its default setting.

CONTINUED ON NEXT PAGE

— 14 —