Specifications, Select video input connector

CSelect video input connector

Select the appropriate mode depending on the connector being used ( pg. 16).

When using S-VIDEO input connector on the front panel, set “FRONT AUX INPUT” to “S-VIDEO”.

When using S-VIDEO IN connector on the rear panel, set “REAR

AUX INPUT” to “S-VIDEO”.

When using VIDEO input connector on the front panel, set “FRONT AUX INPUT” to “VIDEO”.

When using VIDEO IN connector on the rear panel, set “REAR AUX INPUT” to “VIDEO”.

DSelect edit mode

Set the edit mode to “ON” for the VCRs if such a mode is equipped.

●On this VCR, set “PICTURE CONTROL” to “EDIT” ( pg. 15).

ELocate end point

Load the cassette to be edited into the VCR and press PLAY (4), then press PAUSE (9) when you find the end of the scene for which you want to edit.

Press C.RESET so that the counter reading becomes “0:00:00”.

FLocate start point, and engage Insert Editing mode

Press REW (3), then press PAUSE (9) when you find the beginning of the scene for which you want to edit, then press

INSERT.

●The VCR enters the Insert Editing Pause mode. “” and “$” light on the display panel.

●If you want to perform AV Dubbing and replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time, after you press INSERT, press A.DUB also.

GStart editing

Load the source cassette and engage the Play mode of the other component, then press PLAY (4) on the VCR. Insert Editing begins at this point.

●Insert Editing stops automatically when the counter reaches “0:00:00”, and the VCR enters the Play mode.

To stop editing any time during recording

Press STOP (8) on the Remote or STOP/EJECT (0) on the VCR, then engage the Stop mode of the other component.

NOTES:

●Be sure to select “AUTO” for “PICTURE CONTROL” (or

“NORM” when “VIDEO CALIBRATION” is set to “OFF”) after you finish editing ( pg. 15).

●Editing is not possible with a cassette whose record safety tab has been removed.

●The recording speed (SP/EP) is determined by the previous recording to be replaced. If the recording speed changes on the tape to be edited while editing the tape, the inserted picture will be distorted where the recording speed changes.

●When you edit a tape, a small portion of the recording preceding to the editing start point will be erased from the edited tape.

Specifications

GENERAL

Power requirement	: AC 120 Vd, 60 Hz
Power consumption
Power on	:		16 W
Power off	:		1.5 W
Temperature
Operating	: 5°C to 40°C (41°F to 104°F)
Storage	: –20°C to 60°C (–4°F to140°F)
Operating position	:		Horizontal only
Dimensions (W x H x D) :			435 mm x 94 mm x 242 mm
			(17-3/16" x 3-3/4" x 9-3/4")
Weight	: 2.7 kg (5.9 lbs)
Format	: S-VHS/VHS NTSC standard
Maximum recording time
SP	: 210 min. with ST-210 video cassette
EP	:		630 min. with ST-210 video cassette

VIDEO/AUDIO
Signal system	:	NTSC-type color signal and EIA
			monochrome signal, 525 lines/
			60 fields
Recording/Playback	:	DA-4 (Double Azimuth) head helical
system			scan system
Signal-to-noise ratio	:		45 dB
Horizontal resolution
VHS	:		230 lines
S-VHS	:		400 lines
Frequency range
Normal audio	: 70 Hz to 10,000 Hz
Hi-Fi audio	: 20 Hz to 20,000 Hz
Input/Output	:	RCA connectors (IN x 2, OUT x 1)
			S-video connectors (IN x 2, OUT x 1)

TUNER
Tuning system	:		Frequency-synthesized tuner
Channel coverage
VHF	: Channels 2–13
UHF	: Channels 14–69
CATV	:		113 Channels
RF output	:	Channel 3 or 4 (switchable; preset to
			Channel 3 when shipped) 75 ohms,
			unbalanced

TIMER
Clock reference	:		Quartz
Program capacity	:		1-year programmable timer/

8programs

Memory backup for timer is not supported.

ACCESSORIES

Provided accessories	: Infrared remote control unit,
	“AA” battery x 2,
	S-video cable (4-pin),
	RF cable (F-type)

Specifications shown are for SP mode unless specified otherwise. E. & O.E. Design and specifications subject to change without notice.

— 20 —