JVC HR-S5911U specifications Basic Recording, Recording Features

Recording

It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.

Accidental erasure prevention

To prevent accidental recording on a
recorded cassette, remove its record
safety tab. To record on it later, cover
the hole with adhesive tape.	Record safety tab

Basic Recording

ALoad a cassette

Make sure the record safety tab is intact. If not, cover the hole with adhesive tape before inserting the cassette.

●The VCR turns on, and the counter on the on-screen display is reset, automatically.

BSelect recording channel

Press CH+/– or the Number keys on the Remote. Or push the JOG dial, then turn it to the left or right.

●If you connect the TV and the VCR only using the RF connection, press TV/VCR on the Remote so that the VCR mode indicator lights on the display panel, to view the program to be recorded.

CSet tape speed

Press SP/EP. The selected tape speed will appear on the TV screen.

NOTE:

You can select tape speed in the stop mode or during recording pause mode.

DStart recording

On the VCR, press REC (7). Or on the Remote, while holding REC (7), press PLAY (4).

NOTE:

If “VIDEO CALIBRATION” is set to “ON” ( pg. 15) (default setting), the VCR takes about 7 seconds to assess the quality of the tape in use, then recording begins with the picture level optimized.

During recording

Pause recording

Press PAUSE (9).

●Press PLAY (4) to resume recording.

●You can select channel in the recording pause mode.

Stop recording

Press STOP (8) on the	OR Press STOP/EJECT (0) on
Remote.	the VCR.

NOTE:

If the tape reaches its end during recording, the recording stops and “” and “$” on the display panel blink. Press STOP/EJECT (0) on the VCR to eject the cassette or press REW (3) on the Remote to rewind the tape.

Recording Features

Specifying recording length

— Instant Timer Recording (ITR)

During recording, press REC (7) on the VCR repeatedly until the recording length you want appears on the display panel. The record indicator () on the display panel starts blinking.

●Each time you press the button, recording length increases in 30-minute intervals (up to 6 hours).

●The VCR shuts off after recording is finished.

●To cancel an ITR, press STOP (8) on the Remote or STOP/EJECT (0) on the VCR.

Watching one program while recording another

During recording...

●If you connect the TV and the VCR only using the RF connection ( pg. 5) to view pictures from the VCR, press TV/ VCR on the Remote so that VCR mode indicator goes off from the display panel. (The TV broadcast being recorded disappears.)

●If you are using the AV connection ( pg. 5) to view pictures from the VCR, change the TV’s input mode from AV to TV.

Then, select the channel you want to watch, on the TV.

Second Audio Recording

This VCR’s built-in MTS decoder enables reception of Multichannel TV Sound broadcast. To record a SAP program received, set “2ND AUDIO RECORD” to “ON” ( pg. 15).

S-VHS (Super VHS), S-VHS ET or VHS Recording Mode

This VCR can record in S-VHS (Super VHS), S-VHS ET or VHS.

●To record in S-VHS:

Set “S-VHS MODE” to “ON” ( pg. 16). Then, insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the display panel.

The S-VHS recording mode is selected.

●To record in S-VHS ET on a VHS cassette:

Set “S-VHS ET” to “ON” ( pg. 15). Then, insert a cassette marked “VHS”. The S-VHS indicator lights up on the display panel.

●To record in VHS:

Insert a cassette marked “VHS”.

Set “S-VHS ET” to “OFF” ( pg. 15).

●To record in VHS on an S-VHS cassette:

Insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the display panel. Then, set “S-VHS MODE” to “OFF”

( pg. 16). The S-VHS indicator goes off. The VHS recording mode is selected.

NOTE:

When playing back a tape that has been recorded in S-VHS or S-VHS ET, the S-VHS indicator lights up on the display panel regardless of the “S-VHS ET” or “S-VHS MODE” setting.

( pg. 15, 16)

— 11 —