JVC HR-S5911U Audio Dubbing, Insert Editing and AV Dubbing, Select input mode, Start dubbing

Various connection for editing tapes

The following three methods can be used for editing tapes.

●VHS to S-VHS editing (VIDEO-VIDEO connection): Although the picture quality is inherently limited by the original VHS quality, the edited tape has better picture quality than those made by VHS-to-VHS editing.

●S-VHS to VHS editing (VIDEO-VIDEO connection):

Since the original source is recorded in S-VHS mode, the edited tape has better picture quality than those made by VHS-to-VHS editing.

●S-VHS to S-VHS (S-VIDEO connection):

Original picture quality of S-VHS made can be duplicated with minimal picture degradation. This is the best editing method you can use on S-VHS VCRs.

Audio Dubbing

Audio Dubbing replaces the normal audio sound of a previously recorded tape with a new soundtrack.

AMake connections

Connect an audio cable between the VCR’s audio input connectors and the audio component’s audio output connectors.

●When connecting a monaural audio component, use only the VCR’s AUDIO L input connector.

●Audio Dubbing is possible by using the audio input connectors on the front panel or on the rear panel.

This VCR

To AUDIO input

To AUDIO output

CD player, etc.

BSelect input mode

Select “F-1” —when connecting the audio component to the audio input connectors on the front panel.

Select “L-1” —when connecting the audio component to the audio input connectors on the rear panel.

Press AUX or CH+/– on the Remote. Or push the JOG dial, then turn it to the left or right.

CLocate start point, and engage Audio Dubbing mode

Load a cassette and press PLAY (4) on the VCR. Press PAUSE (9) at the point where you want to start dubbing, then press A.DUB.

●The VCR enters the Audio Dubbing Pause mode. “” blinks and “$” lights on the display panel.

DStart dubbing

Engage the Play mode of the audio component, then press PLAY (4) on the VCR. Audio Dubbing begins at this point.

●To pause dubbing, press PAUSE (9). Press PLAY (4) to resume dubbing.

EEnd Audio Dubbing

Press STOP (8) on the Remote or STOP/EJECT (0) on the VCR, then engage the Stop mode of the audio component.

NOTES:

●When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to hear the

Hi-Fi or mixed sound (Hi-Fi + normal soundtracks), press A.MONITOR to select “NORM HI-FI”. ( pg. 9, “Selecting monitor sound”)

●Audio Dubbing stops automatically when the counter reaches “0:00:00”, and the VCR enters the Play mode. Check the counter reading on the screen before dubbing.

●Audio Dubbing is not possible with a cassette whose record safety tab has been removed.

●When playing back an audio-dubbed tape, press A.MONITOR to select the soundtrack you wish to hear. ( pg. 9, “Selecting monitor sound”)

Insert Editing and AV Dubbing

Insert Editing:

You can replace a recorded scene with new scene recorded on another tape or with other material. Both the picture and the sound recorded on the Hi-Fi sound track are replaced at the same time.

AV Dubbing:

You can perform Audio Dubbing and Insert Editing at the same time. This means that the picture and the sounds recorded on the Hi-Fi sound track and on the normal track are replaced at the same time.

●For AV Dubbing, you can edit pictures and sound using different sources; connect a video source to the video input connector, and an audio source to the audio input connectors.

AMake connections

Connect an audio/video cable between the VCR’s audio/video input connectors and the other component’s audio/video output connectors.

●Insert Editing and AV Dubbing are possible by using the audio/ video input connectors on the front panel or on the rear panel.

	This VCR (for recording)
To AUDIO/VIDEO IN		To S-VIDEO IN

Audio/video cable	S-video cable
(not supplied)	(supplied)

To audio/video output To S-video output

Another VCR (for playback)

BSelect input mode

Select “F-1” —when connecting the other component to the audio/video input connectors on the front panel.

Select “L-1” —when connecting the other component to the audio/video input connectors on the rear panel.

Press AUX or CH+/– on the Remote. Or push the JOG dial, then turn it to the left or right.

CONTINUED ON NEXT PAGE

— 19 —