JVC HR-VP682U manual Check contents, Situate VCR, Connect VCR to TV, Final preparation for use

Page 7

EN 7

1 Check contents

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” (☞ pg. 49).

2 Situate VCR

Place the VCR on a stable, horizontal surface.

3 Connect VCR to TV

The following connections are required.

RF Connection

1Disconnect the TV antenna from the TV.

2Connect the TV antenna cable to the ANT. IN terminal on the rear of the VCR.

3Connect the supplied RF cable between the RF OUT terminal on the rear of the VCR and the TV’s antenna input terminal.

AV Connection (improves picture quality during

tape playback.)

If your TV is equipped with audio/video input connectors

1Connect the antenna, VCR and TV as shown in

the illustration.

2Connect an audio/video cable between the AUDIO/VIDEO OUT connectors on the rear of the VCR and the audio/video input connectors on the TV.

4 Connect VCR to power source Connect the AC power plug to an AC outlet.

●The clock and tuner channels will automatically be set when the antenna is connected and when the AC power cord is first connected to an AC power outlet (☞ pg. 8).

(If “Auto” or “CH” is displayed on the front display panel before the VCR is turned on, the clock and tuner channels are being set automatically. Wait until the clock time is displayed on the front display panel before turning on the VCR.)

5Final preparation for use

Turn on the VCR and set the CH3-CH4 switch on the rear (shown below) to either CH3 or CH4 correctly.

●The CH3–CH4 switch is preset to the CH3 position.

Set to CH4 if CH3 is used for broadcasting in your area. (To view the picture from this VCR through this channel, select the same channel on the TV with the CH3–CH4 switch setting on the VCR.)

●You can now perform basic playback (☞ pg. 15) or basic recording (☞ pg. 19).

OUT ANT. IN

R

AUDIO

L

RF OUT

VIDEO

CH3 CH4

Back of VCR

NOTES:

●The VCR channel is the channel on which you can watch the picture from the VCR on the TV when only using the RF connection. The VCR’s CH3-CH4 switch, on the back of the VCR, sets the VCR channel to CH3 or CH4.

●Even if you are using audio/video cables to connect your VCR to your TV, you must also connect it using the RF cable. This will ensure that you can record one show while watching another (☞ pg. 20).

●For full identification of the VCR’s rear panel, refer to the Index ( ☞ pg. 47).

Image 7

Contents HR-VP682U Telephone Number Dear CustomerGrounding or Polarization Power SourcesPower Lines Power Cord ProtectionReplacement Parts AccessoriesDamage Requiring Service CleaningContents Coaxial cable Flat feeder Matching transformer Audio OUT not supplied AC Power CordBasic Connections Antenna or cableFinal preparation for use Check contentsSituate VCR Connect VCR to TVPerform Plug & Play setup Plug & Play SettingWhat to do if Plug & Play setting failed Select language Language SettingAccess Main Menu screen Access Initial Set screenSelect clock set Clock Setting10 EN PreparationsSelect time zone Setting clock semiautomaticallySet Auto Clock to on Select host channelManual Clock Set Setting clock manuallySelect D.S.T. mode 12 ENAutomatically Auto Channel Set Tuner SettingAccess Tuner Set screen Perform Auto Channel SetAdd or skip desired channels Setting channels manuallyAccess Manual Channel Set screen 14 ENLoad a cassette Basic PlaybackChecking tape position Basic Playback Features16 EN Changing display informationSelecting monitor sound Adjusting tracking conditionAutomatic operations after Locating beginning Locating beginning of timerAccess distant code 18 ENSet tape speed BasicRecording Select recording channelWatching one program while recording another Basic Recording Features20 EN Specifying recording lengthAccidental erasure prevention Showing on-screen displayDisplay VCR status on TV screen Erase on-screen displayRapidly Picture Search High-Speed Picture Search Special Effect Playback22 EN Locating particular scenePause during playback Viewing still pictureSkipping unwanted portions Viewing slow motion pictureAccess VCR Plus+ screen VCR Plus+ Timer Programing24 EN Press SP/EP Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Input receiving channel number26 EN VCR Plus+ SetupVCR Plus+ guide channel matching Input guide channel number Access Guide Channel Set screen28 EN Express Timer ProgramingPress SP/EP to set the tape speed To timer-record daily Monday-Friday or weekly serials30 EN Checking program settingsSelect program to modify Confirm overlapping programsOverlapping programs blink on the screen Select Function Useful Function SettingsChange setting 32 ENWhen this function is set to OFF When this function is set to onFor Example 34 ENHi-Fi and normal tracks Normal and Hi-Fi tracks. The main audio is not recorded36 EN PreventingConnection Edit To Or From AnotherSet TV brand code TV Brand Setting38 EN Turn on the TVEx. To set the Remote to RCA Cable Box Brand SettingTurn on the cable box Operate cable boxOperate DBS receiver DBS Receiver Brand Setting40 EN Turn on the DBS receiverPlug in VCR Changing Remote Control CodeSet remote control code for Remote Unplug VCR42 EN TroubleshootingTimer Recording Can the VCR indefinitely remain in still mode? 44 ENWhat happens if the tape reaches its end during recording? List of terms Manual setting Preparation Semiauto settingExpress timer recording VCR PLUS+ setupFront panel 46 ENFront display panel On-screen display Rear panel48 EN How to use the RemoteRemote Specifications 50 EN HOW to Locate Your JVC Service CenterLimited Warranty HR-VP682U