JVC HR-VP646U manual Turn on the TV, SET TV Brand Code, Operate TV, Special Feat Ures

Page 48

48EN

SPECIALFEATURES

TV Multi-Brand Remote

Control

POWER

TV

1 2 3

TV/VCR

4

5

6

NUMBER

MBR SET

7 8 9

0

ENTER

CH

TV VOL +/–

1 3 Á

¦ 7 8

4 ¢

STOP

The VCR's remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below. *The default setting is JVC code 01.

TURN ON THE TV

1 Turn the power on using the TV's remote control.

SET TV BRAND CODE

2 Refer to the chart below. While holding down TV on the VCR's remote control, press MBR SET and enter your TV’s brand code using the NUMBER keys, then press STOP. Follow the example shown below.

Once you have set the remote control to operate the TV, you don’t have to repeat this step until you replace your remote control’s batteries.

PANASONIC has two codes. If the TV does not function with one code, try entering the other.

OPERATE TV

3 First, while holding down TV, press POWER on the remote to see if the TV’s power goes off as it should. If it does, try other operations.

The POWER, TV/VCR, CH, TV VOL +/– and NUMBER keys on the remote can all be used to operate the TV. *For some brands of TV, you must press ENTER after having pressed the NUMBER keys.

To operate your TV, while holding down TV, press the corresponding button: POWER, TV/VCR, CH, NUMBER keys (or ENTER). TV VOL +/– can be used without holding down TV.

(Ex.) To set remote control to RCA 05:

TV

MBR SET 0 AUX

5

7STOP

 

 

 

Release

Hold

Press in succession

 

down

 

 

 

NOTE:

Depending on the type of TV, there may be cases where some or all functions cannot be operated using the remote control.

TV BRAND NAME

BRAND CODE

JVC

01

MAGNAVOX

02

MITSUBISHI

03

PANASONIC

04, 11

RCA

05

SHARP

06

SONY

07

TOSHIBA

08

ZENITH

09

HITACHI

10

SAMSUNG

12

SANYO

13

SEARS

13

 

 

Image 48
Contents HR-VP646U Dear Customer Do not place the VCRImportant Product Safety Instructions Product and cart combination Should be moved with care. QuickContents Basic Connections Plug & Play Setup Initial SettingsPlug & Play Auto Clock Set/Auto Tuner SetTurn on the TV and select the VCR channel 3 or 4 or AV mode LanguageClock Select Mode Access Select ScreensEN Initial Settings Select Host ChannelSelect D.S.T. Mode Select Time ZoneMake Corrections ManualTuner Information Access Tuner SET Screen Access AFC ScreenMake Selection Store or Skip Desired ChannelCable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCRAccess Custom SET Screen Access VCR PLUS+ SET-UP ScreenSelect Cable BOX Output Channel Set Cable Box Output ChannelAccess Cable BOX Turn on Cable BOXBrand SET Screen Return to NormalVCR Plus+ Setup Access Main Menu ScreenAccess Custom SET Screen Input Receiving Channel Number Check Input Data Access Guide Channel SET ScreenPress CH5, Shuttle DBS Receiver Control To VCRConnect Controller DBS receiverReturn to Custom SET Screen Set DBS Receiver Output ChannelTurn on DBS Receiver Enter DBS Receiver BrandSet DBS Receiver Brand DBS Receiver Brand SET, then press OKSimple Playback Load a CassetteFind Program Start Point Start PlaybackSimple Recording Playback Features Engage Manual Tracking Mode Adjust Manual TrackingLayback and Recording Features RE-ENGAGE Automatic TrackingVideo Stabilizer Access Function SET Access SuperimposeSuperimpose Access Audio Monitor Select The SoundtrackMix Access Distant Code Start SearchSkip Over Unwanted Sections Activate Counter MemoryReturn to Counter Position Zero Access Special Make ConnectionFunction Screen AV Compu Link PlaybackEnable AV Compu Link Playback ExampleActive Video Calibration Recording PlaybackRecording Features Engage TV ModeReset Counter to Zero Select Channel for ViewingAccess 2ND Audio Stereo And SAP Second Audio ProgramTo Record SAP Programs To Record Stereo ProgramsVCR Plus+ Timer Programming EN Timer RecordingCheck Input Data Engage Timer Mode Press just once to access the Auto Timer screenPress TIMER. The VCR turns off automatically CHECK/CORRECT Input DataOn-Screen Timer Programming Access ON-SCREENAccess Program SET MenuTo timer-record a regular TV program received on the VCR CatvCable BOX Output is set to OFF pg.16 Disengage Timer Access Program SET ScreenCancel a Program RE-ENGAGE TimerAccess Auto Timer Auto TimerInstant Timer Recording ITR Engage ITR ModeSET Recording Duration Press REC on the front panelEdit To Or From Another Edit From a Camcorder SET RECORDER’S InputMode Access AUX Input Return to FunctionSET Screen Plus %ÞTV Multi-Brand Remote Control Turn on the TVSET TV Brand Code Operate TVCable Box Multi-Brand Remote Control Turn on the Cable BOXEnter Cable BOX Brand Operate Cable BOXEN Special Features DBS Receiver Multi-Brand Remote ControlTurn on the DBS Receiver Operate DBS ReceiverUnplug Vcrs Power SET Remote ControlPlug in Power Cord Turn VCR Power onTroubleshooting Cassette gets stuck partwayTimer again Re-perform the VCR Plus+ setup Doesn’t work properlyProcedure pg Those in the previous area Has not been programmed correctly Cassette is automaticallyOther Problems OubleshootingQuestions and Answer S E N PlaybackMBR Multi-Brand Remote Code Setting List Of TermsIndex Select DBS Receiver Output ChannelFront View EN Index Rear ViewInstalling Batteries How To UseEIA monochrome signal 20C to 60C -4F to140FMaximum recording time Frequency-synthesized tunerHOW to Locate Your JVC Service Center For Servicing Only in U.S.A. E NWarranty Only in U.S.A Limited WarrantyMemo HR-VP646U