JVC HR-VP646U manual Basic Connections

Page 6

6ENINSTALLINGYOURNEWVCR

Basic Connections

Antenna or Cable

ANT. IN

 

 

(Antenna or Cable input)

 

 

Coaxial Cable

 

 

Flat Feeder

AC Power

Matching Transformer

Cord

(not supplied)

 

Back of VCR

 

AC

 

Audio Cable

 

Outlet

 

(not supplied)

RF OUT

 

 

 

 

 

Video Cable (not supplied)

RF Cable (supplied)

75 ohm terminal

1

2

3

4

CHECK CONTENTS

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” (pg. 60).

SITUATE VCR

Place the VCR on a stable, horizontal surface.

CONNECT VCR TO TV

The connection method you use depends on the type of TV you have.

RF Connection

To Connect To A TV With NO AV Input Terminals . . .

a– Disconnect the TV antenna from the TV.

b– Connect the TV antenna cable to the ANT. IN jack on the rear of the VCR.

c– Connect the supplied RF cable between the RF OUT jack on the rear of the VCR and the TV’s antenna terminal. Set TV on CH3 or CH4 corre- sponding to the CH3 – CH4 switch setting on the back of the VCR.

AV Connection

To Connect To A TV With AV Input Terminals . . .

a– Connect the antenna, VCR and TV as shown in the illustration.

b– Connect an Audio/Video Cable between the AUDIO OUT and VIDEO OUT jacks on the rear of the VCR and the AV IN jacks on the TV. Set your TV in video input mode or A/V input mode. Refer to the TV Instruction Manual.

CONNECT VCR TO

POWER SOURCE

Connect the power plug to an AC outlet.

The clock and tuner channels will automatically be

TV

NOTES:

Back of VCR

CH3 CH4

set when the antenna is connected and when the AC

is first connected to the VCR (pg. 7).

(If "Auto" or "CH" is displayed on the front display

panel before the VCR is powered on, the clock and

tuner channels are being set automatically. Wait for

the time to be displayed on the front display panel

before powering on the VCR.)

FINAL PREPARATION FOR USE

The VCR channel is the channel on the TV which will display the audio and video signals from the VCR. The VCR's CH3- CH4 switch, on the back of the VCR, sets the VCR channel to CH3 or CH4.

The CH3–CH4 switch is preset to the CH3 position.

Set to CH4 if CH3 is used for broadcasting in your area and set the channel on the TV to correspond to the VCR's CH3– CH4 switch setting.

If RF connection to TV is used, when switching from VCR to TV mode and from TV to VCR it may be necessary to issue a CH UP and then CH DOWN on TV to obtain a good quality picture.

Even if you are using AV cables to connect your VCR to your TV, you must also connect it using the RF cable. This will ensure that you can record one show while watching another (pg. 36).

For full identification of the VCR's rear panel, refer to the Index (REAR VIEW pg. 58).

5

Power on the VCR and select the VCR channel (3 or 4) by setting the switch on the rear of the VCR as shown in the illustration.

You can now perform simple playback (pg. 23) or simple recording (pg. 24).

Image 6
Contents HR-VP646U Dear Customer Do not place the VCRImportant Product Safety Instructions Product and cart combination Should be moved with care. QuickContents Basic Connections Plug & Play Plug & Play SetupInitial Settings Auto Clock Set/Auto Tuner SetTurn on the TV and select the VCR channel 3 or 4 or AV mode LanguageClock EN Initial Settings Select ModeAccess Select Screens Select Host ChannelMake Corrections Select D.S.T. ModeSelect Time Zone ManualTuner Information Make Selection Access Tuner SET ScreenAccess AFC Screen Store or Skip Desired ChannelAttach Controller Cable Box ControlSituate Controller Connect Cable BOX to VCRSelect Cable BOX Output Channel Access Custom SET ScreenAccess VCR PLUS+ SET-UP Screen Set Cable Box Output ChannelBrand SET Screen Access Cable BOXTurn on Cable BOX Return to NormalVCR Plus+ Setup Access Main Menu ScreenAccess Custom SET Screen Input Receiving Channel Number Check Input Data Access Guide Channel SET ScreenPress CH5, Shuttle Connect Controller DBS Receiver ControlTo VCR DBS receiverReturn to Custom SET Screen Set DBS Receiver Output ChannelSet DBS Receiver Brand Turn on DBS ReceiverEnter DBS Receiver Brand DBS Receiver Brand SET, then press OKFind Program Start Point Simple PlaybackLoad a Cassette Start PlaybackSimple Recording Playback Features Layback and Recording Features Engage Manual Tracking ModeAdjust Manual Tracking RE-ENGAGE Automatic TrackingVideo Stabilizer Access Function SET Access SuperimposeSuperimpose Access Audio Monitor Select The SoundtrackMix Access Distant Code Start SearchSkip Over Unwanted Sections Activate Counter MemoryReturn to Counter Position Zero Function Screen Access SpecialMake Connection AV Compu Link PlaybackEnable AV Compu Link Playback ExampleActive Video Calibration Recording PlaybackReset Counter to Zero Recording FeaturesEngage TV Mode Select Channel for ViewingTo Record SAP Programs Access 2ND AudioStereo And SAP Second Audio Program To Record Stereo ProgramsVCR Plus+ Timer Programming EN Timer RecordingCheck Input Data Press TIMER. The VCR turns off automatically Engage Timer ModePress just once to access the Auto Timer screen CHECK/CORRECT Input DataAccess Program SET On-Screen Timer ProgrammingAccess ON-SCREEN MenuTo timer-record a regular TV program received on the VCR CatvCable BOX Output is set to OFF pg.16 Cancel a Program Disengage TimerAccess Program SET Screen RE-ENGAGE TimerAccess Auto Timer Auto TimerSET Recording Duration Instant Timer Recording ITREngage ITR Mode Press REC on the front panelEdit To Or From Another Edit From a Camcorder SET RECORDER’S InputMode SET Screen Access AUX InputReturn to Function Plus %ÞSET TV Brand Code TV Multi-Brand Remote ControlTurn on the TV Operate TVEnter Cable BOX Brand Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXTurn on the DBS Receiver EN Special FeaturesDBS Receiver Multi-Brand Remote Control Operate DBS ReceiverPlug in Power Cord Unplug Vcrs PowerSET Remote Control Turn VCR Power onTroubleshooting Cassette gets stuck partwayProcedure pg Those in the previous area Timer againRe-perform the VCR Plus+ setup Doesn’t work properly Has not been programmed correctly Cassette is automaticallyOther Problems OubleshootingQuestions and Answer S E N PlaybackIndex MBR Multi-Brand Remote Code SettingList Of Terms Select DBS Receiver Output ChannelFront View EN Index Rear ViewInstalling Batteries How To UseMaximum recording time EIA monochrome signal20C to 60C -4F to140F Frequency-synthesized tunerHOW to Locate Your JVC Service Center For Servicing Only in U.S.A. E NWarranty Only in U.S.A Limited WarrantyMemo HR-VP646U