JVC HR-VP646U manual Timer again, Has not been programmed correctly Cassette is automatically

							E	N	53
TIMER RECORDING
		SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
1.	Timer recording won’t work.		● The clock and/or the timer have		Set the clock and/or timer correctly.
			been set incorrectly.
			● The timer is not engaged.		Press TIMER and check to make sure
					that TIMER appears on the front
					display panel.
			● The VCR has not been set up properly.		Re-perform the set-up procedures.
					Make sure you have compensated for
					Guide Channel and VCR or cable
					box channel number mismatches
					(☞ pg. 18).
2.	On-screen timer programming		● Timer recording is in progress.		Timer programming can’t be performed
	won’t work.				when timer recording is in progress.
					Wait until it finishes.
3.	TIMER and ] on the front		● The timer is engaged but there’s no		Load a cassette with the record safety
	display panel won’t stop blinking.		cassette loaded.		tab intact, or with the hole covered
					with adhesive tape.
4.	The cassette is automatically		● The loaded cassette has had its		Remove the cassette and cover its
	ejected, and TIMER and ] on the		record safety tab removed.		hole with adhesive tape, or replace it
	front display panel won’t stop				with a cassette on which the safety
	blinking.				tab is intact.
5.	TIMER blinks for 10 seconds and		● TIMER has been pressed when there		Check the programmed data and re-
	the timer mode is disengaged.		are no programs in memory, or the		program as necessary, then press
			timer record program information		TIMER again.
			has not been programmed correctly.
6.	The cassette is automatically		● The end of tape was reached during		The program may not have been
	ejected, the power shuts off and		timer recording.		recorded in its entirety. Next time
	TIMER and ] won’t stop				make sure you have enough time on
	blinking.				the tape to record the entire program.
7.	Cable channels are not automatically		● The Controller is not properly		Connect the Controller correctly
	switched during timer recording.		connected to the VCR.		(☞ pg. 15).
			● The output channel selected in the		After confirming your cable box’s
			Cable Box Output screen is incorrect.		output channel number, re-access the
					Cable Box Output screen and select
					the correct number (☞ pg. 16).
			● The cable box’s power is off.		Make sure the power is on before
					timer recording starts.
8.	Satellite channels are not automati-		● The Controller is not properly		Connect the Controller correctly
	cally switched during timer		connected to the VCR.		(☞ pg. 20).
	recording.		● The output channel selected in the		After confirming your DBS receiver’s
			DBS Receiver Output screen is		output channel number, re-access the
			incorrect.		DBS Receiver Output screen and
					select the correct number (☞ pg. 21).
			● The DBS receiver’s power is off.		Make sure the power is on before
					timer recording starts.
9.	Timer recording begins as sched-		● Even though you don't use an		Set "CABLE BOX OUTPUT" to "OFF"
	uled, but the channel is always		external Cable Box, "CABLE BOX		(☞ pg. 16).
	incorrect.		OUTPUT" is set to "ON".
10.We moved, and now VCR Plus+			● The receivable stations in the new area		Re-perform the VCR Plus+ setup
	doesn’t work properly.		are received on different channels than		procedure (☞ pg. 18).
			those in the previous area.
11.	“PROGRAM FULL” is displayed on		● All 8 programs of the VCR’s timer		Wait until a space in memory clears,
	the VCR Plus+ screen.		memory are used.		or cancel unnecessary program
					information (☞ pg. 42).