JVC Model HR-DVS1U manual Cable Box Control, Situate Controller, Attach Controller

Page 15

Cable Box

Control

Suggested Location

Place the cable box on top of the VCR. Attach the VCR's Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.

ATTENTION:

The Controller can also control a DBS receiver. If both a cable box and a DBS receiver are used, position the controller so its signal reaches the remote control sensors of both the cable box and DBS receiver.

Cable box

Controller

Your VCR(suggested

locations)

Cable box

Controller

Transmitter

Connected to

ANT. IN

Your VCR

CABLE

BOX

EN15

This procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the VCR to automatically switch the cable box channel during timer-recording. The Controller is effective for recording shows that have been programmed using the VCR Plus+ system

(pg. 40) or Express Timer Programming (pg. 44).

Situate And Connect

Controller

SITUATE CONTROLLER

1 Place the Controller so that the path between its transmitter and the cable box’s remote sensor is unobstructed.

ATTACH CONTROLLER

2 Fasten securely using the supplied adhesive strip.

CONNECT CABLE BOX TO VCR

3 The connection method depends on the type of cable box you have.

If your cable box has AUDIO and VIDEO OUT connectors . . .

. . . connect them to the AUDIO and VIDEO IN connectors on your VCR. Set the VCR to channel "L-1" for the rear AUDIO and VIDEO IN connectors to use the cable box.

If your cable box doesn’t have AUDIO and VIDEO

OUT connectors . . .

. . . connect the antenna output connector on the cable box to the ANT. IN connector on the rear of your VCR. Set the VCR tuner to the same channel as the cable box RF output (see page 16 also).

NOTE:

When connecting your cable box refer to its instruction manual.

CONNECT CONTROLLER

TO VCR

4 Connect to the CABLE BOX connector on your VCR.

About Your Cable Box

This VCR has two separate methods to control your Cable Box.

The VCR's Wireless Remote Control Unit can control your Cable Box.

This eliminates the need for a separate Cable Box Remote Control Unit.

The VCR's Controller can also control your Cable Box.

This allows the VCR to change your Cable Box's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 67. To set up the Controller go to page 16.

Image 15
Contents HR-DVS1U Do not place the VCR Dear CustomerAntenna Installation Instructions InstallationBefore YOU Install Your NEW VCR USEServicing Contents Connections Not supplied Connect VCR to TVSupplied AC Outlet ANT. in Antenna or Cable inputAuto Clock Set/Auto Tuner Set Plug & Play SetupPlug & Play EN I Nitial Sett IngsLanguage EN Initial Settings Access Main Menu ScreenAccess Initial SET Screen Access Clock SET ScreenSET Auto Clock to on Select Host ChannelSemi-Auto SET Time Select D.S.T. ModeSelect Time Zone Return to Normal ScreenSet Receivable Channels Access Tuner SET ScreenTuner SETScreen Access Main Menu ScreenAccess Manual Channel SET Add Or Delete a ChannelConnect Cable BOX to VCR Cable Box ControlSituate Controller Attach ControllerOutput Channel Access Cable BOX SETTurn on Cable BOX Select Cable BOXAccess Cable BOX Brand SET Screen Enter Cable BOX BrandBrand Code DBS receiver DBS Receiver ControlConnect DBS Receiver to VCR Your VCR ControllerTurn on the TV and select the AV mode SET DBS Receiver Brand JVC Dish Network Echostar Dish NetworkJVC Simple Playback Simple Recording Activate SLOW-MOTION Playback FeaturesPause During Playback Activate FRAME-BY Frame PlaybackStill Picture/Frame-By-Frame Layback and Recording FeaturesActivate HIGH-SPEED Search Variable-Speed Search/ Reverse Motion PlaybackVHS Access Mode SET ScreenSelect Superimpose SET Mode SuperimposeRE-ENGAGE Automatic Tracking Engage Manual Tracking ModeAdjust Manual Tracking Access Distant CodeStop Repeat Start RepeatPicture Control VHS deck only Select The Soundtrack Video StabilizerThen press OK or #to Digital TBC/NR VHS deck onlyArrow to Digital TBC NR by pressing CH 5 orThen press OK or #to set Arrow to VHS Mode SET by pressing CH 5orArrow to Digital R3 by Pressing CH 5 or %ÞActivate Playback Zoom During PlaybackMove Screen Stop ZoomSound YOU Hear Access DV Mode SETSound Mode Selection 32kHz Mode SettingVHS deck only Active Video CalibrationRecording Recording Features Resume Recording Select 2ND Audio Record SET ModeMode Locate Start PointAccess VHS Mode SET Select S-VHS ModeVHS Super VHS, S-VHS Pressing CH5 or%Þ Arrow to S-VHS ET byNumber VCR Plus+ Timer ProgrammingEN Timer Recording Access VCR PLUS+ ScreenCheck Program Data Engage Timer ModeArrow to Initial SET Changing VCR Plus+ SettingInput Receiving Channel Number Access Guide Channel SET ScreenEx. When inputting the Guide Channel number 6 for WNJUInd Input Guide Channel NumberExpress Timer Programming SET Program DateSET Channel Number Power Program Access Program Check ScreenAccess Program Screen Check, Cancel And Revise ProgramsAuto SP→EP Timer Select Auto SP →EP Timer SET ModeThen press OK or # to set Timer RecordingAuto Timer Arrow to Auto TimerPress REC on the front panel Instant Timer Recording ITREngage ITR Mode SET Recording DurationDirection Tape DubbingLoad Cassettes Select DubbingFor the playing deck Normal DubbingPause Dubbing END DubbingRandom Assemble Editing Program Editing Memory 8 programmes x 8 scenesLocate EDIT-IN Point Pause Locate EDIT-OUT PointUSE FADE/WIPE Effect on Scene Transition If Necessary Register Additional ScenesEditing Fader B.W Menu Effect Fader WhiteFader Black Fader MosaicSelect Recording Deck Edit From a CamcorderMake Connections Load a CassetteVHS Deck only Select AUX Input SET ModeControl SET Mode Select Edit for PictureEdit To Or From Another Make ConnectionsVideo Start Player SET RECORDER’S Input ModeOUTPUT1 Setting Select Edit for PICEngage Audio Dubbing SET Input ModeAudio Dubbing Select Recording DeckEND Audio Dubbing When monitoring the sound during Audio Dubbing,VHS Deck only DV Insert Editing SP Mode OnlyInsert Editing Locate END PointEND Insert Editing Reset the CounterEngage Insert Editing Start EditingConnecting To a Video Titler Connecting To a Printer Digital printerVHS Operate TV SET Remote Control ModeTurn on the TV SET TV Brand CodeCable BOX Brand Name Brand Code Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXTurn on the DBS SET Remote ControlSpecial Features DBS Receiver Multi-Brand Remote ControlCord Unplug Vcrs PowerPlug in Power Cord Turn VCR Power onCassette gets stuck partway Then insert the cassetteRecording won’t start That ä appears on the front display Panel Re-perform the set-up proceduresTimer again Point is not dubbedPlus+ system doesn’t work properly Re-perform the VCR Plus+ setupProcedure pg RoubleshootingPlayback Quest Ions and Answers ENFront View IndexRear View VHS Display Panel Remote Control Component Video Connection Express Timer ProgrammingMBR Multi-Brand Remote Code Setting List Of TermsSpeci Fications For Servicing Only in U.S.A HOW to Locate Your JVC Service CenterLimited Warranty Warranty Only in U.S.A. ENEN M EMO Memo HR-DVS1U