JVC Model HR-DVS1U Reset the Counter, Engage Insert Editing, Start Editing, END Insert Editing

Page 63

TOP	PLAY

INSERT

PAUSE

.DUB A

T	W	3
1	2	3
		2
4	5	6
7	8	9
C.RESET	0	4
C.RESET
		PLAY
1	DV	VHS
STOP		PAUSE
STOP
	3

JOG/SHUTTLE

JOG

SHUTTLE

EN63

	RESET THE COUNTER
5	(VHS deck only)
	Press C.RESET to change the counter display to
	"0:00:00".
	LOCATE START POINT
	Determine the edit-in point (the beginning of the
	segment to be replaced) using the JOG/SHUTTLE
6 controls or pressing ª£and PAUSE.
	● Be sure to engage the Still mode at the edit-in point.

ENGAGE INSERT EDITING

7	Press INSERT.

	● Your VCR enters the Insert-Pause mode. ( , and
	light up on the front display panel.)
	● The TV screen changes from the still picture to the
	input source you are going to record.

	START EDITING
	Load the source cassette and play back the segment
	that is to be inserted. When you reach the start of the
8 section of the source tape that you wish to insert, press
	PLAY to start the tape in your VCR; Insert Editing begins
	at this point.

● and are displayed on the front display panel.

END INSERT EDITING

9 VHS deck

At counter "0:00:00", Insert Editing will stop automati- cally while the tape continues running in the Play mode. If you wish to stop Insert Editing before the specified edit-out point, press C.RESET.

DV deck

Press STOP to stop the tape in the DV deck.

FOR AV INSERT EDITING (VHS deck only)

If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time...

In step 7 above, after you press INSERT, press A. DUB. also. (andblink andlights up on the display panel.)

NOTES:

●Insert Editing cannot be performed on a VHS/S-VHS cassette that has had its record safety tab removed, or on a Mini DV cassette that has had its erase protection switch set to "SAVE".

●In insert editing, the recording speed (SP/EP) is determined by the previous recording to be replaced. If the previous recording's speed changes within a single edit, the inserted picture will be distorted at the switching point. (VHS deck only)

●A small portion of the recording which precedes an insert edit may become erased.

●Insert Editing is also possible using the rear connectors. When using these connectors, be sure to select the correct REAR AUX INPUT. To select the correct REAR AUX INPUT ("VIDEO" or "S-VIDEO"), follow steps 5 – 7 from the "Edit From A Camcorder" section, ☞ pg 57.

●Insert Editing is not possible using the DV IN/OUT connector.

Image 63

Contents HR-DVS1U Do not place the VCR Dear CustomerAntenna Installation Instructions InstallationBefore YOU Install Your NEW VCR USEServicing Contents Connections Not supplied Connect VCR to TVSupplied AC Outlet ANT. in Antenna or Cable inputAuto Clock Set/Auto Tuner Set Plug & Play SetupPlug & Play EN I Nitial Sett IngsLanguage EN Initial Settings Access Main Menu ScreenAccess Initial SET Screen Access Clock SET ScreenSET Auto Clock to on Select Host ChannelSemi-Auto SET Time Select D.S.T. ModeSelect Time Zone Return to Normal ScreenSet Receivable Channels Access Tuner SET ScreenTuner SETScreen Access Main Menu ScreenAccess Manual Channel SET Add Or Delete a ChannelConnect Cable BOX to VCR Cable Box ControlSituate Controller Attach ControllerOutput Channel Access Cable BOX SETTurn on Cable BOX Select Cable BOXAccess Cable BOX Brand SET Screen Enter Cable BOX BrandBrand Code DBS receiver DBS Receiver ControlConnect DBS Receiver to VCR Your VCR ControllerTurn on the TV and select the AV mode SET DBS Receiver Brand JVC Dish Network Echostar Dish NetworkJVC Simple Playback Simple Recording Activate SLOW-MOTION Playback FeaturesPause During Playback Activate FRAME-BY Frame PlaybackStill Picture/Frame-By-Frame Layback and Recording FeaturesActivate HIGH-SPEED Search Variable-Speed Search/ Reverse Motion PlaybackVHS Access Mode SET ScreenSelect Superimpose SET Mode SuperimposeRE-ENGAGE Automatic Tracking Engage Manual Tracking ModeAdjust Manual Tracking Access Distant CodeStop Repeat Start RepeatPicture Control VHS deck only Select The Soundtrack Video StabilizerThen press OK or #to Digital TBC/NR VHS deck onlyArrow to Digital TBC NR by pressing CH 5 orThen press OK or #to set Arrow to VHS Mode SET by pressing CH 5orArrow to Digital R3 by Pressing CH 5 or %ÞActivate Playback Zoom During PlaybackMove Screen Stop ZoomSound YOU Hear Access DV Mode SETSound Mode Selection 32kHz Mode SettingVHS deck only Active Video CalibrationRecording Recording Features Resume Recording Select 2ND Audio Record SET ModeMode Locate Start PointAccess VHS Mode SET Select S-VHS ModeVHS Super VHS, S-VHS Pressing CH5 or%Þ Arrow to S-VHS ET byNumber VCR Plus+ Timer ProgrammingEN Timer Recording Access VCR PLUS+ ScreenCheck Program Data Engage Timer ModeArrow to Initial SET Changing VCR Plus+ SettingInput Receiving Channel Number Access Guide Channel SET ScreenEx. When inputting the Guide Channel number 6 for WNJUInd Input Guide Channel NumberExpress Timer Programming SET Program DateSET Channel Number Power Program Access Program Check ScreenAccess Program Screen Check, Cancel And Revise ProgramsAuto SP→EP Timer Select Auto SP →EP Timer SET ModeThen press OK or # to set Timer RecordingAuto Timer Arrow to Auto TimerPress REC on the front panel Instant Timer Recording ITREngage ITR Mode SET Recording DurationDirection Tape DubbingLoad Cassettes Select DubbingFor the playing deck Normal DubbingPause Dubbing END DubbingRandom Assemble Editing Program Editing Memory 8 programmes x 8 scenesLocate EDIT-IN Point Pause Locate EDIT-OUT PointUSE FADE/WIPE Effect on Scene Transition If Necessary Register Additional ScenesEditing Fader B.W Menu Effect Fader WhiteFader Black Fader MosaicSelect Recording Deck Edit From a CamcorderMake Connections Load a CassetteVHS Deck only Select AUX Input SET ModeControl SET Mode Select Edit for PictureEdit To Or From Another Make ConnectionsVideo Start Player SET RECORDER’S Input ModeOUTPUT1 Setting Select Edit for PICEngage Audio Dubbing SET Input ModeAudio Dubbing Select Recording DeckEND Audio Dubbing When monitoring the sound during Audio Dubbing,VHS Deck only DV Insert Editing SP Mode OnlyInsert Editing Locate END PointEND Insert Editing Reset the CounterEngage Insert Editing Start EditingConnecting To a Video Titler Connecting To a Printer Digital printerVHS Operate TV SET Remote Control ModeTurn on the TV SET TV Brand CodeCable BOX Brand Name Brand Code Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXTurn on the DBS SET Remote ControlSpecial Features DBS Receiver Multi-Brand Remote ControlCord Unplug Vcrs PowerPlug in Power Cord Turn VCR Power onCassette gets stuck partway Then insert the cassetteRecording won’t start That ä appears on the front display Panel Re-perform the set-up proceduresTimer again Point is not dubbedPlus+ system doesn’t work properly Re-perform the VCR Plus+ setupProcedure pg RoubleshootingPlayback Quest Ions and Answers ENFront View IndexRear View VHS Display Panel Remote Control Component Video Connection Express Timer ProgrammingMBR Multi-Brand Remote Code Setting List Of TermsSpeci Fications For Servicing Only in U.S.A HOW to Locate Your JVC Service CenterLimited Warranty Warranty Only in U.S.A. ENEN M EMO Memo HR-DVS1U