JVC Model HR-DVS1U manual SET DBS Receiver Brand, JVC Dish Network Echostar Dish Network, Jvc

Page 20

20ENINITIALSETTINGS(cont.)

7

ACCESS DBS RECEIVER BRAND SET SCREEN

Press OK.

SET DBS RECEIVER BRAND

CH	8

Press the appropriate NUMBER keys to enter the DBS Receiver Code from the following list, then press OK.

DBS RECEIVER BRAND SET

4 0

PRESS NUMBER KEY (0–9)

THEN (OK) TO TEST PRESS (MENU) TO END

T

W

1 2 3

2

4 5 6

NUMBER

7 8 9

0 4

1

DV

VHS

3

BRAND	CODE
JVC (DISH Network)	51
ECHOSTAR (DISH Network)	51
PRIMESTAR	50
SONY (DSS)	41
RCA (DSS)	40

●After OK is pressed, the program currently received through the DBS receiver will appear for about 10 seconds.

●If the DBS receiver's channel changes to the channel listed below for your brand of DBS receiver, setting is complete. Press OK and "DBS RECEIVER CONTROL IS ON" appears on the screen for about 5 seconds, then it returns to the normal screen.

JVC [ 100

ECHOSTAR [ 100

PRIMESTAR [ 55

SONY [ 205

RCA [205

●If the DBS receiver's channel does not change as shown above, press CH 5° or %Þ to move the highlight bar (arrow) to "NO", then press OK. Re- enter the correct code.

OK

NOTES:

●It is possible that the Controller will not work with all types of DBS receiver.

●If your DBS receiver doesn’t respond to the code, you can’t use the Controller to change satellite channels. In this case, make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.

●The VCR can only change the satellite channel through the Controller during timer recording.

●If your DBS receiver is one that can’t be operated with a remote control (because it has no remote sensor), you can’t use the Controller to change its channels. Make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.

●If you are unable to set the Controller, please contact JVC toll free at 1-800-252-5722.

Image 20

Contents HR-DVS1U Dear Customer Do not place the VCRInstallation Antenna Installation InstructionsServicing Before YOU Install Your NEW VCRUSE Contents Connections Connect VCR to TV Supplied AC OutletANT. in Antenna or Cable input Not suppliedPlug & Play Setup Plug & PlayEN I Nitial Sett Ings Auto Clock Set/Auto Tuner SetLanguage Access Main Menu Screen Access Initial SET ScreenAccess Clock SET Screen EN Initial SettingsSemi-Auto SET Auto Clock to onSelect Host Channel Select D.S.T. Mode Select Time ZoneReturn to Normal Screen SET TimeAccess Tuner SET Screen TunerSET Set Receivable ChannelsAccess Main Menu Screen Access Manual Channel SETAdd Or Delete a Channel ScreenCable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCRAccess Cable BOX SET Turn on Cable BOXSelect Cable BOX Output ChannelBrand Code Access Cable BOX Brand SET ScreenEnter Cable BOX Brand DBS Receiver Control Connect DBS Receiver to VCRYour VCR Controller DBS receiverTurn on the TV and select the AV mode JVC SET DBS Receiver BrandJVC Dish Network Echostar Dish Network Simple Playback Simple Recording Playback Features Pause During PlaybackActivate FRAME-BY Frame Playback Activate SLOW-MOTIONLayback and Recording Features Activate HIGH-SPEED SearchVariable-Speed Search/ Reverse Motion Playback Still Picture/Frame-By-FrameAccess Mode SET Screen Select Superimpose SET ModeSuperimpose VHSEngage Manual Tracking Mode Adjust Manual TrackingAccess Distant Code RE-ENGAGE Automatic TrackingStart Repeat Stop RepeatPicture Control VHS deck only Video Stabilizer Select The SoundtrackDigital TBC/NR VHS deck only Arrow to Digital TBCNR by pressing CH 5 or Then press OK or #toArrow to VHS Mode SET by pressing CH 5or Arrow to Digital R3 byPressing CH 5 or %Þ Then press OK or #to setZoom During Playback Move ScreenStop Zoom Activate PlaybackAccess DV Mode SET Sound Mode Selection32kHz Mode Setting Sound YOU HearActive Video Calibration VHS deck onlyRecording Recording Features Select 2ND Audio Record SET Mode ModeLocate Start Point Resume RecordingVHS Super VHS, S-VHS Access VHS Mode SETSelect S-VHS Mode Arrow to S-VHS ET by Pressing CH5 or%ÞVCR Plus+ Timer Programming EN Timer RecordingAccess VCR PLUS+ Screen NumberEngage Timer Mode Check Program DataChanging VCR Plus+ Setting Arrow to Initial SETAccess Guide Channel SET Screen Ex. When inputting the Guide Channel number 6 for WNJUIndInput Guide Channel Number Input Receiving Channel NumberSET Channel Number Express Timer ProgrammingSET Program Date Power Access Program Check Screen Access Program ScreenCheck, Cancel And Revise Programs ProgramSelect Auto SP →EP Timer SET Mode Auto SP→EP TimerTimer Recording Auto TimerArrow to Auto Timer Then press OK or # to setInstant Timer Recording ITR Engage ITR ModeSET Recording Duration Press REC on the front panelTape Dubbing Load CassettesSelect Dubbing DirectionNormal Dubbing Pause DubbingEND Dubbing For the playing deckLocate EDIT-IN Point Random Assemble EditingProgram Editing Memory 8 programmes x 8 scenes Locate EDIT-OUT Point USE FADE/WIPE Effect on Scene Transition If NecessaryRegister Additional Scenes PauseEditing Menu Effect Fader White Fader BlackFader Mosaic Fader B.WEdit From a Camcorder Make ConnectionsLoad a Cassette Select Recording DeckSelect AUX Input SET Mode Control SET ModeSelect Edit for Picture VHS Deck onlyVideo Edit To Or From AnotherMake Connections SET RECORDER’S Input Mode OUTPUT1 SettingSelect Edit for PIC Start PlayerSET Input Mode Audio DubbingSelect Recording Deck Engage Audio DubbingWhen monitoring the sound during Audio Dubbing, END Audio DubbingDV Insert Editing SP Mode Only Insert EditingLocate END Point VHS Deck onlyReset the Counter Engage Insert EditingStart Editing END Insert EditingConnecting To a Video Titler VHS Connecting To a PrinterDigital printer SET Remote Control Mode Turn on the TVSET TV Brand Code Operate TVCable Box Multi-Brand Remote Control Turn on the Cable BOXOperate Cable BOX Cable BOX Brand Name Brand CodeSET Remote Control Special FeaturesDBS Receiver Multi-Brand Remote Control Turn on the DBSUnplug Vcrs Power Plug in Power CordTurn VCR Power on CordRecording won’t start Cassette gets stuck partwayThen insert the cassette Re-perform the set-up procedures Timer againPoint is not dubbed That ä appears on the front display PanelRe-perform the VCR Plus+ setup Procedure pgRoubleshooting Plus+ system doesn’t work properlyQuest Ions and Answers EN PlaybackIndex Front ViewRear View VHS Display Panel Remote Control Express Timer Programming MBR Multi-Brand Remote Code SettingList Of Terms Component Video ConnectionSpeci Fications HOW to Locate Your JVC Service Center For Servicing Only in U.S.AWarranty Only in U.S.A. EN Limited WarrantyEN M EMO Memo HR-DVS1U