Magnavox VRB411AT, VRB611AT owner manual Checking or Cancelling Timer Recordings

Page 36

36 Timer Recording (cont’d)

 

Checking or Cancelling Timer Recordings

 

1

 

With the VCR on and in VCR position (the VCR light will appear

 

on the display panel), press the VCR button, then press the

1

MENU button.

2

 

Press the PLAY/o button or the STOP/p button to select

 

PROGRAM, then press the F.FWD/B button.

 

3

 

Press the PLAY/o button or the STOP/p button to select

 

PROGRAM REVIEW, then press the F.FWD/B button.

 

The timer recording information for the program in the lowest

 

numbered slot will appear on the screen. If no timer recordings

 

are set, nothing will happen when you press the F.FWD/B button.

 

2-4

POWER

VCR/TV

 

EJECT

VCR

TV

 

CBL/DBS

 

PLAY

 

 

REW

 

 

F.FWD

 

STOP

 

 

MENU

STATUS/EXIT

CLEAR

1

2

3

 

4

5

6

CH

 

7

8

9

 

ENTER

ALT. CH

0VOL

SPEED

TIME SEARCH

PAUSE/STILL

 

REC/OTR

MEMORY

SLOW

MUTE

5

4

Press the F.FWD/B button repeatedly to review all pro- grammed timer recordings. If you don’t press the F.FWD/B button within 10 seconds, the VCR will automatically display infor- mation about the next programmed timer recording. This will continue until all timer recordings have been displayed. Then the menu will disappear.

5

To cancel the timer recording displayed, press the CLEAR button. Either the display will disappear or information about other timer recordings will appear. If you do not press any other buttons, the display will disappear after all timer recordings have been displayed.

6

Repeat steps 1 - 4 to make sure you have cleared the cor- rect timer recording.

Helpful Hints

•CLASH may flash on the screen when you finish setting a timer recording. This means that the timer recording you just programmed and another timer record- ing overlap. The current timer recording will not take place. You may choose to cancel the overlapping timer recording.

•To stop a started timer recording, press the STOP/EJECT button on the VCR.

•If the power fails for more than one minute, programmed timer recordings will be lost. If this occurs, repeat the steps on pages 11 and 15 before reset- ting the timer recordings.

•If the preset time for a timer recording comes up during an OTR, the OTR has priority. A message will remind you when the timer recording was scheduled to begin. You may let the OTR continue; the timer recording will not take place. Or, stop the OTR and turn off the VCR immediately. The timer recording will

take place if you turn off the VCR before the timer recording’s scheduled start time.

See page 47 for more hints.

Page 35 Page 37
Image 36
Page 35 Page 37
Contents VRB411AT VRB611AT Dear Philips product owner For Customer UseThis bolt of lightning indi- cates uninsulated material Model No Serial NoFeatures Safety PrecautionsIntroduction Table of Contents Before Using Your VCR Hookups without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRHookups with a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Cable Signal Cable Box/DBS Recording One Channel/Watching AnotherTV’s Antenna Hookups with a Stereo TV VRB611VRB411 Press the VCR button, then press the Power button Turning on Your VCR2Turn on the TV Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button Press the Menu buttonVRB611 only Automatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock Manual Clock SettingDo each step within 60 seconds of the previous step Setting the Clock cont’d Enter a 0 before a single-digit numberAutomatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Press the VCR buttonLanguage Selection Setting the Remote to Operate a TV Your VCR remote control may operate your TV. If the remote2Find Your codeRemote Control Buttons VOLume o/p Button Press to adjust the volume of your TVEject Button VCR ButtonRemote Control Buttons cont’d TV ButtonPress to operate the TV On-Screen Status Displays Status Display example onlyIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFTimer Light VCR Display PanelCassette Compartment VCR LightREWind Button Power Button FWD Fast Forward ButtonRemote Sensor Video In JackRear Panel Playing VHS Quasi Play Back SqpbRead and follow the steps below to play a tape 1Turn on the TV 2Insert a tape in the VCRRecording If the VCR light appears on the display panel, go to . IfVCR light does not appear, press the VCR/TV button once RECord light will appearRecording One Channel/Watching Another One-Touch Recording OTR CH12 Timer Recording DailyTimer Recording cont’d Time OFF To Correct Push Clear To END Push ExitPress the STATUS/EXIT button. Program WAS COM Tape SpeedsChecking or Cancelling Timer Recordings Rerecording Tape Duplication RF coaxial cableVCR SET UP, then press the F.FWD/B button Repeat PlayPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Press the STATUS/EXIT button to see the status displayTime Search Press the VCR button Press the Time Search buttonSpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Understanding On-Screen Displays Specifically…Monitor Multi-Channel Television Sound System VRB611 only cont’d Press the RECord/OTR button to start recordingHi-Fi Stereo Sound System VRB611 only Blue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Renewed Index Page Page Page Supplied Accessories
Top Page Image Contents