6.PAUSE/STILL button– Press to temporarily stop the tape during recording or to view a still picture during playback.
Frame Advance function– Press to advance the picture by one frame at a time during still mode.
7.POWER button– Press to turn VCR on and off. Press to activate timer recording, when the timer pro- gram has been set.
8.VCR/TV button– Press to select TV or VCR mode.
VCR position: to view playback, to monitor video recordings or watch TV using the VCR tuner.
TV position: to watch TV or to view one program while recording another.
9.Remote sensor window– Receives the infrared signals from the remote control.
10.Indicators
POWER indicator– Indicates that the power is turned on.
VCR/TV indicator– Indicates that the VCR is in the VCR position.
TAPE IN indicator– Indicates that there is a tape in the VCR.
TIMER indicator– Indicates that the timer recording or OTR has been set.
REC indicator– Indicates that it is recording. Flashes when a recording has been paused.
11.TAPE SPEED button– Press to choose the desired recording speed : SP/SLP. (only on the VCR)
12.CHANNEL Up or Down buttons– Press to select the desired channels for viewing or recording.
Tracking function– Press to minimize video ‘noise’ (lines or dots on screen) during playback (only on the VCR) or slow mode.
Press to stabilize the picture in the Still mode when the picture begins to vibrate vertically.
13.RECORD button– Press for manual recording.
OTR button– Press to activate One Touch Record- ing. (only on the VCR)
14.MENU button– Press to display the menu on the TV screen. Press to exit the menu on the TV screen.
15.NUMBER buttons– Press to select desired channels for viewing or recording. To select channels from 1 to 9, first press "0" button then 1 to 9. (only on the remote control)
+100 button– When selecting cable channels which are higher than 99, press this button first, then press the last two digits. (To select channel 125, first press "+100" button then press "2" and "5"). (only on the remote control)
16.DISPLAY button– Press to display the current time, channel number, real time tape counter, and other in- formation on the TV screen. (only on the remote con- trol)
Each time you press this button, TV screen will change as shown. The status display (STOP, PLAY etc.) and the tape speed display (SP, LP (playback only), or SLP) will disappear after 5 seconds.
<OFF mode> | <COUNT mode> |
| <CLOCK mode> | ||
|
| STOP |
| STOP | 5:40PM |
|
|
|
|
| CH 02 |
| Press | Press |
| ||
| once SP 0:12:34 | once SP |
| ||
Press once
17.SLOW button– Press to start slow motion playback. (only on the remote control)
18.COUNTER MEMORY button– Press to set counter memory on and off. (only on the remote control)
19.COUNTER RESET button– Press to reset counter to 0:00:00. (only on the remote control)
EXIT button– Press to exit the menu on the TV screen. (only on the remote control)
20.SEARCH MODE button– Press to perform a Time Search or an Index Search. (only on the remote con- trol)
21.Power cord– Connect to a standard AC outlet (120V/60Hz).
22.AUDIO OUT jack– Connect to the audio input jack of your audio equipment or another VCR.
23.AUDIO IN jack– Connect to the audio output jack of your audio equipment or another VCR.
24.ANT. IN terminal– Connect to an antenna, Cable system or Satellite system.
25.VIDEO OUT jack– Connect to the video input jack of your video camera or another VCR.
26.VIDEO IN jack– Connect to the video output jack of your video camera or another VCR.
27.CH3/CH4 selector switch– Use to select a video output channel (3 or 4) for VCR playback.
28.ANT. OUT terminal– Connects to the antenna input terminal on your TV.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow.
2)Insert 2 "AA" penlight batteries into the battery com- partment in the direction indicated by the polarity
3)Replace the cover.
Install 2 X AA battery
- 5 - | EN |
| 0J01 |
H7836