Fisher FVH-T610 Checking the Program Timer, Clearing the Program Timer

Page 36

SC4H/UF (FVH-T610 GB) Fri. Jan., 07/2000

PROGRAM TIMER RECORDING

Setting a Program Timer Recording Using the Buttons on the VCR

If the remote control does not operate or is not available you can use the buttons on the VCR front panel to set a program timer recording.

NOTE: Eject the cassette tape, before proceeding with the steps below.

1Press and hold the REC button on the front panel for about 5 seconds.

The Timer program menu appears.

If the clock has not yet been set, the Clock set menu appears.

If necessary, the clock can also be set using the CHANNEL l (or j) and FF buttons. (Refer to the next step for button functions.)

2Use the CHANNEL l (or j) and FF buttons on the VCR front panel to program the timer.

CHANNEL button: To select numbers or switch

settings

FFbutton:To select the next item

NOTE: If you enter the wrong number or setting, press the REW button to return to the wrong number or setting, then enter the correct one.

3When the recording tape speed is set, press the FF button on the front panel to save the settings.

4When finished, press the REC button on the front panel to exit from the menu.

5Load a cassette.

6Press the POWER button.

NOTES:

œDaily or weekly recording, or the program type cannot be set using this method.

œOnce a program timer recording has been set, it cannot be erased using the buttons on the VCR front panel.

Checking the Program Timer

1Turn on the power (TV and VCR).

2Set the TV to channel 3 or 4.

3Press the MENU button. The main MENU appears.

4Press the OK button.

The programmed recordings are listed.

NOTE: To display the program type or rating, press the TYPE button after selecting the desired program using the ù (or û) button.

5When finished, press the MENU button to exit the menu.

6Press the POWER button.

The VCR power turns off and the timer is set to the recording standby mode.

The Timer icon (n) appears.

Clearing the Program Timer

1Follow steps 1 – 4 in “Checking the Program Timer”.

2Press the ù (or û) button to select the program to be cleared.

3Press the CLEAR button.

The erase confirmation screen appears.

4Press the CLEAR button again. (To cancel the erase procedure, press the SET button.)

The selected timer program is erased from the program memory.

5When finished, press the MENU button to exit the menu.

6Press the POWER button.

Changing the Program Timer

1Follow the steps under “Clearing the Program Timer” to erase the program that you wish to change.

2Follow the steps under “Timer Programming” to add a new timer program.

35

Page 35 Page 37
Image 36
Page 35 Page 37
Contents FVH-T610 Precautions Moisture Condensation ProblemsLocation Avoiding Electric Shock or FireFeatures AccessoriesContents VHS Video Cassette Tapes Locations of Controls and Indicators Front PanelAuto A/V Selection Locations of Controls and Indicators Indicator PanelOperation Icons Example of IndicationsBack Panel Multibrand Universal Remote Control Locations of ControlsMultibrand Universal Remote Control Battery Installation and OperationSetting the remote control code Using the remote controlCatv DSS SprucerBasic ANTENNA/CABLE Connections VCRWhen the TV does not have a built-in cable converter When you have both cable and pay TV scrambled channelsAlternative Cable TV Connections Cable converter/decoder output channel setup Alternative Cable TV ConnectionsImportant Notes When you have a stereo monitor TV When you have a monitor TV and a stereo systemAUDIO/VIDEO Connections Stereo ConnectionsInitial Setup RF output channel setting ruleIf no XDS signal is available in your area Before startingInitial Setup Channel Selection ConvenienceManual Erase Manual ProgrammingMultifunction ON-SCREEN Displays ON-SCREEN Menu Displaying the On-Screen MenusMain Menu Options Displaying the VCR Setup Menus Before starting VCR Setup Menu OptionsON-SCREEN Menu Setting the Clock Automatic Clock AdjustmentClock set menu appears Setting the Clock Manual Clock SettingStandard/Daylight Time Adjustment Changing the Menu Language Programming ChannelsChannel Programming Viewing TV only Playing a Rental TapePlayback of Copyguarded Tapes Normal Playback Manual Picture ControlAutomatic Picture Control DPC picture control screen appearsTracking Control Adjustments Tracking ControlManual Tracking Control Tapes with Hi-Fi SoundRec. List Super Feature Recording source Indicator showsRecording Recording One Program While Viewing AnotherRecording Smart Speed Record FunctionRec. List Recording Contents List Super Rec. List SuperEntering the Program Type Type input menu will be displayed on screenMTS Indicators MTS Mode SelectionStereo/SAP Recording Audio Output Mode Special Playback Zero Search Index SearchIndex Search Operation Index Search e will be displayed on-screenProgram Timer Recording Timer ProgrammingTimer program menu appears End time AM/PM setting will be entered automaticallyProgram Timer Recording Type and Smart Time Rec. setting menu appearsSmart Time Record Function Checking the Program Timer Clearing the Program TimerChanging the Program Timer Using Timer Recording for Several Programs Timer Setting NotesProgram Recording Order Quick Timer Recording QTR Auto SettingAppears on the VCR display Child Lock Forward picture search begins Sound is mutedMaintenance Head Care and CleaningCabinet Cleaning AV indicator L1 is displayed instead of a channel numberTroubleshooting Guide Symptom Possible Cause Corrective ActionSpecifications General SpecificationsElectrical Specifications Other Specifications
Top Page Image Contents