Sylvania DVC840G Quick Use Guide, Connections, Installing the Batteries for the Remote

Quick Use Guide

1
	Connections	3 Press [B] to start Auto Set Up.	CH 01
Please refer to “Basic TV Connection” on the front page			AUTO SET UP
before you use this unit.

✄

RF Output Channel

If channel 3 has been already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Press [OUTPUT] on the unit so that the VCR OUTPUT light is lit.

•If noise appears on the TV screen, press [VCR/TV] on the remote control.

4)Press [PLAY B] once.

5)After a few seconds, press and hold [PLAY B] on the unit for 3 seconds.

•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4.

6)Press [STOP C] to stop playback.

2	Installing the Batteries for the Remote
	Control
	1	2	3

3 VCR/DVD Switching

OPEN/CLOSE

POWER SPEED AUDIO /EJECT

		1	2	3
					SKIP/CH.
		4	5	6
					VCR/TV
		7	8	9
	VCR button	DISPLAY	VCR	DVD	SLOW
					PAUSE
			0	+10
	DVD button
			PLAY
	OUTPUT		STOP
		REC/OTR
		MENU		ENTER
VCR	DVD	SETUP	TOP MENU		RETURN
	DVD OUTPUT	MODE	ZOOM	MODE	C. RESET
				SEARCH	CLEAR/
	light	T-SET	ANGLE	REPEAT	A-B
		SUBTITLE

OUTPUT button

VCR OUTPUT light

VCR MODE

Press [VCR] on the remote control.(Verify that the VCR OUTPUT light is lit.)

DVD MODE

Press [DVD] on the remote control.(Verify that the DVD OUTPUT light is lit.)

Hint

•Pressing only [OUTPUT] on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control.

4	Turn On the Unit for the First Time
	VCR
1	Turn on the TV and set it to channel 3.
	• If channel 3 has been already occupied for broadcasting,
	see “RF Output Channel” section.
2	Select your language in the first time you turn on this unit.
	Then press [B] to go to next step.	LANGUAGE SELECT
	POWER	BENGLISH	[ON]
		FRANCAIS

or ESPAÑOL

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

YES NO

Yes Press [MENU] to exit.

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memorized in this unit by using [SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).

•If “AUTO SET UP” appears on the TV screen again, check the cable connections. Then, press [B] once again.

5	Clock Set Up
	VCR
1	Press [MENU] and select “CLOCK SET“.	- M E N U -
	Then press [B] to go to next step.	TIMER PROGRAMMING
		AUTO REPEAT [OFF]
		CHANNEL SET UP
	MENU	BCLOCK SET
		LANGUAGE SELECT

or

•If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2.

2	Select the current month.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	– –	– – – –
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
3	Select the current day.		CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 2	– – – –
		MONTH DAY			YEAR
	or	HOUR MINUTE			AM/PM
		– –	:	– –	– –
4	Select the current year.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 2	2 0 0 6
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
5	Select the current hour.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY			YEAR
		1 0	/	0 2 MON 2 0 0 6
	or	HOUR MINUTE			AM/PM
		0 5	:	– –	– –
6	Select the current minute.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 2 MON 2 0 0 6
		HOUR MINUTE			AM/PM
	or	0 5	:	4 0	– –
7	Select “AM” or “PM”.		CLOCK SET
		MONTH DAY			YEAR
	or	1 0	/	0 2 MON 2 0 0 6
		HOUR MINUTE			AM/PM
		0 5	:	4 0	P M AM
					BPM
8	To exit the CLOCK SET screen

– 27 – EN