JVC SR-DVM70EU manual Digital Audio Dubbing, Input Setting, Example Dubbing to an MD

64 EN EDITING

DECODER:		Digital Audio Dubbing
To use a decoder connected to the [L-2 IN/DECODER]
connector.
	You can dub selected audio from a DVD or Audio CD disc to a
NOTES:
● If you have a satellite receiver or a decoder connected to the [L-2	digital audio device.
IN/DECODER] connector, be sure to set AL-2 SELECTB back to	However, it is not possible to dub copy-protected discs.
appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to the	● Turn on the TV and select the AV mode.
[L-2 IN/DECODER] connector, leave AL-2SELECTB set to	● Slide the TV/CABLE/SAT/DVD switch to DVD.
AVIDEOB.
	Example: Dubbing to an MD
● When AL-2 SELECTB is set to ASAT VIDEOB and ASAT S-VIDEOB,
ASATB appears on the TV screen or front display panel instead of				Recorder
AL-2B.
● If AL-1 OUTPUTB is set to ASCART S-VIDEOB, it is not possible to
set AL-2 SELECTB to ADECODERB or ASAT VIDEOB.
● If AL-1 OUTPUTB is set to ASCART RGBB, it is not possible to set
AL-2 SELECTB to ADECODERB or ASAT S-VIDEOB.
● If AL-1 OUTPUTB is set to ACOMPONENTB and AL-2 SELECTB to
ASAT VIDEOB, ASAT S-VIDEOBor ADECODERB, be sure to
connect the [L-1 IN/OUT] connector with a TV.			Digital audio device
● If AL-2 SELECTB is set to ASAT S-VIDEOB, be sure to set AL-1
			(MD deck, etc.)
OUTPUTB to ASCART S-VIDEOB.

●The BNC and S-Video output do not support the satellite receiver function. Make use of the L-1output when viewing images from

the satellite receiver.				Coaxial cable	Optical cable
				(not supplied)	(not supplied)
F-1 Input Setting
Set AF-1 INPUTB to the appropriate mode depending on the				To [DIGITAL	To [DIGITAL AUDIO
				AUDIO OUT	OUT (OPTICAL)]
connector (VIDEO or S-VIDEO) being used on the front panel.
				(COAXIAL)]
			Player
1 Perform steps 1 and 2 of AL-1 Output And L-1 Input SettingB
(A pg. 63).
2 Press FG to select AF-1 INPUTB, then press ENTER.
3 Press FG to select the	DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP INITIAL SET UP
appropriate setting, then press
	REC/PLAY SET UP DISPLAY SET VIDEO IN/OUT
ENTER.	MONITOR TYPE		4:3LB		Rear of unit
4 Press SET UP to complete the
	F-1 INPUT		VIDEO
setting.	L-1 OUTPUT		S-VIDEO
	L-1 INPUT		SCART VIDEO
	L-2 SELECT		VIDEO
	SET UP	ENTER	SELECT WITH @ THEN PRESS [ENTER]
	EXIT	SELECT	PRESS [SET UP] TO EXIT	Note for connection:

Remove the protection cap from the optical cable.

* The boldface settings below indicate the settings at your purchase.

8F-1 INPUT ^ VIDEO / S-VIDEO VIDEO:

When connecting an appliance to the [VIDEO] input connector, set to AVIDEOB.

S-VIDEO:

When connecting an appliance to the [S-VIDEO] input connector, set to AS-VIDEOB.

1Connect the unit and a digital audio device using either an optional optical cable or an optional coaxial cable.

2Place a disc on the unit and load an MD on the connected digital audio device.

3Select the audio to be dubbed.

4Start playback slightly before the actual point from where you wish to start dubbing.

5Press W to pause playback.

6Select the input mode on the connected digital audio device.

7Press I to start playback on the unit.

8Start recording on the digital audio device.

9Stop recording on the digital audio device. Then press o to stop playback on the unit.

NOTE:

There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts.