ADS Technologies USB Instant DVD manual Service and Warranty

Page 34

SER VICE AND W ARRANTY

Service and Warranty:

Service:

If you require assistance with the installation, operation, or application of your ADS Technologies, Inc. product there are several options available to you as described in the technical support section of this manual.

The ADS Technologies technical support and customer service staff can aid in solving many problems. Our technical support department is available to repair any ADS Technologies product. You or your dealer must return products to our factory for repair or warranty replacement.

Return/Replacement:

Each individual computer store or dealer sets product returns policies for their customers. ADS Technologies, Inc. cannot be responsible for the actions or policies set by our dealers. If you desire to return the product for a refund, you must get the refund from the dealer or store you purchased the product from. If you purchased the product directly from ADS please see the “Terms and Conditions of Sale” on the reverse side of your sales invoice.

Returns to ADS Technologies, Inc. are for repair or warranty replacement only. If you need to return product to ADS Technologies, Inc. for repair or replacement you must follow these steps:

1.Call our Technical Support department at (562) 926-4338 to obtain a Return Merchandise Authorization (RMA) number.

2.The RMA number is valid for 30 days.

3.Ship the product to the ADS factory with the RMA number marked on the inside and outside of the package. If there is no RMA number on the package or the RMA number has expired, the shipment will be refused. ADS will not be liable for lost or mis-shipped products.

4.Replacement product cannot be shipped to you until the defective product has been

received by ADS.

5.Once the product is received at the factory it will be tested and then repaired or replaced.

6.Turn around time is approximately one week. A repaired or replacement product will be shipped back to you.

32

CapWiz manual.p65

32

6/4/2002, 12:22 PM

Image 34

Contents USB USB Instant DVDUSB USB USB USB USB USB USB USB USB USB USB Table of Contents USB Instant DVD User’s GuideInstalling and running VideoStudio Configuring VideoStudio Exporting your movie Instant DVD Overview Three Ways to Capture Video Capwiz Basic Video Capture & PlaybackBurn a VCD or DVD movie to disk Video Studio DVD-WIZARD AT the Finish StepCreate Video and Send Back to Tape Single Step Capture & Burn a CD or DVD disk Create VCD or DVD SlideshowGetting Started Check USB Instant DVD ContentsSystem Requirements Wire It Up USB Instant DVDWire It Up! cont’d Check your diagram of connectors on your Sound CardF 9 ft. Audio out to TV/VCR Plug It In & Install Device Drivers and Software Insert USB Instant DVD CDSet your VGA Resolution Optimize System For Best PerformanceVerify Hardware Installation Windows Audio Mixer Settings Windows Audio Mixer SettingsInstallation Summary Start Making DVD Movies USB Instant DVD Capture Wizard Step One Open Cap WizUSB Instant DVD Capture Wizard cont’d USB Instant DVD Capture Wizard cont’d USB Instant DVD Capture Wizard cont’d Naming Files Ready to Preview and Capture VideoBegin Recording Playback Options Playback to TV or VCRPlayback List Box Video Format Menu OptionsVideo Inputs/Outputs Brightness/ColorVideo Playback Timing Audio/Video Delay ParametersVideo Capture Timing ControlMenu Options Options Recording OptionsMenu Options Advanced PlaybackAudio Devices Split Stream AudioDisk space About Help Using CapWizMenu Options Help System InfoUSB Instant DVD Wizard Features Audio ParametersUSB Instant DVD Wizard Features cont’d Television standards Ntsc countriesService and Warranty Warranty FCC InformationUlead VideoStudio 6 Quick Start Start Capturing Video with Video Studio in 5 Easy StepsNorth & South America International Table of Contents Exporting your movie Big picture An introduction to digital videoAn introduction to Mpeg MPEG-1How VideoStudio works To install VideoStudio Installing and running VideoStudioTo run VideoStudio Instant DVD Setup Configuring VideoStudioTo check the setup of VideoStudio for analog interface Getting around VideoStudio Options PanelPreview Bar Zoom controls Selected rangeStoryboard and Timeline Insert media files Trim handleSave Project Settings and CommandsNavigator buttons Trash CanHome System VolumePrevious Mark in / outLibrary To add media clips to the LibrarySteps to create your movie Start Start Creating a new projectTo create a new project using New Project To open an existing projectSelecting a template Checklist for successful video capture CaptureDirect capturing Mpeg video To capture video in Mpeg formatCapturing still images To capture still imagesStoryboard Storyboard ModeLarger storyboard display Storyboard Mode Timeline ModeTo switch to different tracks Timeline ModeOptions Panel SmartRender and Play Project button To play the preview area onlyTo delete temporary preview files Preview Files ManagerInserting a clip into the Timeline To insert a video clip into the TimelineTo trim a clip from the Timeline Trimming a clipTo trim a clip with the Trim Bar To trim a clip in the Options Panel Working with clipsTo create multiple copies of a single clip Capturing still images in the Storyboard Step Using color clipsTo insert a color clip in the Color Library Creating effects EffectTo add a transition Customizing effects Inserting video/image in the Overlay track OverlayTo insert a clip to the Overlay Track Customizing overlays Title Editing TabTo add a text title Creating text titlesAnimation Tab TypeTo create a vertical text title Creating vertical text titlesTo modify a text title Alignment buttonsRolling & scrolling Using the LibraryTo apply a preset animation effect To add a title from the LibraryTo create fading titles Fading in & outPutting it all together To create extended creditsAudio Load audioVoiceover Tab Music TabCreating and saving a video file FinishTo render a movie To render partially Click Create Video File in the Options PanelVideo Save Options Ulead VideoStudio TabMPEG-1 file for VCD To create an MPEG-1 file for VCDMPEG-2 file for DVD To create an MPEG-2 file for DVDCreating an audio file Creating a DVD / VCD / Svcd TitleProject Playback To create an audio fileBurning DVD/VCD/SVCD Exporting your movieTo burn your DVD/VCD/SVCD title in Ulead DVD Wizard Click Create DVD/VCD/SVCD to start the burning process Recording back to a camcorder or VCR To record a movie to your camcorder or VCRShortcuts Need more help? Glossary AnalogNLE Mydvd 3.5 User Guide MyDVD Get Started Quick Capturing Video with MyDVDVideo Capture from Instant DVD Single Step Capture and Burn a CD or DVD disk What is the minimum VGA setting? USB Instant DVD Helpful Hints