Magnavox CMWD2206 A owner manual Quick Use Guide, Connections, Control VCR/DVD Switching

Quick Use Guide

1 Connections

Please refer to “Basic TV Connection” on the front page before you use this unit.

RF Output Channel

If channel 3 has been already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Press [SOURCE] on the unit so that the VCR SOURCE light is lit.

•If noise appears on the TV screen, press [VCR/TV] on the remote control.

4)Press [PLAY B] once.

5)After a few seconds, press and hold [PLAY B] on the unit for 3 seconds.

•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4.

6)Press [STOP C] to stop playback.

2	Installing the Batteries for the Remote
	Control
	1	2	3
3	VCR/DVD Switching
here			STANDBY-ON			OPEN/CLOSE
				SPEED	AUDIO	/EJECT
cut			1	2	3
				0	+10	SKIP/CH.
			4	5	6
						VCR/TV
			7	8	9
		VCR button				SLOW
			DISPLAY	VCR	DVD	PAUSE
		DVD button		PLAY
		SOURCE button
				STOP
	VCR	DVD	RECORD
		SOURCE	MENU		ENTER
			SETUP	TOP MENU		RETURN
			MODE	ZOOM	SEARCH	CLEAR/
		DVD SOURCE light			MODE	C. RESET
			T-SET	ANGLE	REPEAT	A-B
			SUBTITLE
		VCR SOURCE light

VCR MODE

Press [VCR] on the remote control. (Verify that the VCR SOURCE light is lit.)

DVD MODE

Press [DVD] on the remote control. (Verify that the DVD SOURCE light is lit.)

Hint

•Pressing only [SOURCE] on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control.

4	Turn on the Unit for the First Time
	VCR
1	Turn on the TV and set it to channel 3.
	• If channel 3 has been already occupied for
	broadcasting, see “RF Output Channel” section.
2	Select your language when turning this unit on for the first time.
	Then press [B] to go to next step.
		LANGUAGE SELECT
	STANDBY-ON	B ENGLISH	[ON]
		FRANCAIS

ESPAÑOL

or

3	Press [B] to start Auto Set Up.		CH 01
		AUTO SET UP

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

YESNO

Yes Press [MENU] to exit.

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memorized in this unit by using [SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).

•If “AUTO SET UP” appears on the TV screen again, check the cable con- nections. Then, press [B] once again.

5	Clock Setup
	VCR
1	Press [MENU] and select “CLOCK SET“.	- M E N U -
	Then press [B] to go to next step.	TIMER PROGRAMMING
		AUTO REPEAT [OFF]
	MENU	CHANNEL SET UP
		B CLOCK SET
		LANGUAGE SELECT

or

•If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2.

2	Select the current month.	MONTH DAY		YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/ – –	– – – –
		HOUR MINUTE		AM/PM
	or	– –	: – –	– –
3	Select the current day.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY		YEAR
		1 0	/ 0 5	– – – –
		HOUR MINUTE		AM/PM
	or	– –	: – –	– –
4	Select the current year.	MONTH DAY		YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/ 0 5		2 0 0 9
		HOUR MINUTE		AM/PM
	or	– –	: – –	– –
5	Select the current hour.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY		YEAR
		1 0	/ 0 5 MON	2 0 0 9
		HOUR MINUTE		AM/PM
	or	0 5	: – –	– –
6	Select the current minute.	MONTH DAY		YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/ 0 5 MON	2 0 0 9
		HOUR MINUTE		AM/PM
	or	0 5	: 4 0	– –
7	Select “AM” or “PM”.		CLOCK SET
		MONTH DAY		YEAR
		1 0	/ 0 5 MON	2 0 0 9
	or	HOUR MINUTE		AM/PM
		0 5	: 4 0	P M AM
					B PM
8	To exit the CLOCK SET screen

25 EN